Official Paper

RRB ALP CBT-II (Fitter) Official Paper (Held On: 02 May, 2025 Shift 1) (Previous Year Paper)

175 questions · 150 minutes · with answers · free

Attempt as Timed Mock Test

Part A (100 questions)

1

The resistivity of a conductor depends on which of the following factors?

  1. ((a))

    Area of ​​the conductor

  2. ((b))

    Mass of the conductor

  3. ((c))

    Nature of the conductor

  4. ((d))

    Diameter of conductor

Show Answer
Answer: ((a))

Area of ​​the conductor

2

Which of the following statements is correct regarding negative work done?

  1. ((a))

    The work done cannot be negative.

  2. ((b))

    When the force is perpendicular to the displacement, the work done is negative.

  3. ((c))

    When the force acts opposite to the direction of displacement, the work done is negative.

  4. ((d))

    When the force and displacement are in the same direction, the work done is negative.

Show Answer
Answer: ((a))

The work done cannot be negative.

3

In areas with hot climate, white colour of the exterior walls of the house is preferred because

  1. ((a))

    White color keeps the interior environment of the house cool by reflecting sunlight.

  2. ((b))

    White color makes the wall more durable.

  3. ((c))

    White color makes the house brighter by absorbing more sunlight.

  4. ((d))

    The white color looks good.

Show Answer
Answer: ((a))

White color keeps the interior environment of the house cool by reflecting sunlight.

4

The sum of Yash's and his father's ages is 90 years. When Yash's age equals his father's present age, he will be five times his son Suraj's present age. When Yash's age equals his father's present age, Suraj's age will be 12 years more than Yash's present age. Find Suraj's present age.

  1. ((a))

    15 years

  2. ((b))

    18 years

  3. ((c))

    12 years

  4. ((d))

    16 years

Show Answer
Answer: ((a))

15 years

5

What should come in place of question mark (?) in the given alphanumeric series?

G5, I10, L15, N20, Q25, S30, ?

  1. ((a))

    W35

  2. ((b))

    V35

  3. ((c))

    V40

  4. ((d))

    U35

Show Answer
Answer: ((a))

W35

6

Which of the following is a supplementary protocol that allows non-ASCII data to be sent via e-mail?

  1. ((a))

    HTTPS

  2. ((b))

    Multipurpose Internet Mail Extensions (MIME)

  3. ((c))

    DNS

  4. ((d))

    Mailing Lists

Show Answer
Answer: ((a))

HTTPS

7

Which of the following options best describes the primary function of digital signatures in electronic communications?

  1. ((a))

    It automatically stores all electronic documents for future reference.

  2. ((b))

    It encrypts the entire message content to ensure confidentiality.

  3. ((c))

    It verifies the identity of the sender and ensures the integrity of the message.

  4. ((d))

    This allows the recipient to edit the document before adding the signature.

Show Answer
Answer: ((a))

It automatically stores all electronic documents for future reference.

8

The areas of three adjacent faces of a solid cuboid are 216 cm², 114 cm² and 19 cm². Find the volume (in cm³) of the cuboid.

  1. ((a))

    684

  2. ((b))

    955

  3. ((c))

    532

  4. ((d))

    880

Show Answer
Answer: ((a))

684

9

Read the given statements and conclusions carefully. Assuming that the information given in the statements is true, even if it seems to be at variance from commonly known facts, decide which of the given conclusions logically follows from the statements.

Statements:

Some bananas are litchis.

All litchis are kiwis.

Some kiwis are strawberries.

Conclusions:

  1. All bananas are kiwis is a possibility.
  2. All kiwis are litchis.
  1. ((a))

    Only conclusion 1 follows

  2. ((b))

    Only conclusion 2 follows

  3. ((c))

    Neither conclusion 1 nor 2 follows

  4. ((d))

    Both conclusions 1 and 2 follow

Show Answer
Answer: ((a))

Only conclusion 1 follows

10

Which of the following ecosystems has very low temperatures and frozen soil?

  1. ((a))

    Desert

  2. ((b))

    Tropical rainforest

  3. ((c))

    Pasture

  4. ((d))

    Tundra

Show Answer
Answer: ((a))

Desert

11

If A is an acute angle and p tan A = n sec A, then find the value of p2−n2pn\frac{p^2 - n^2}{pn}.

  1. ((a))

    cot A .cos A

  2. ((b))

    sin A .cos A

  3. ((c))

    tan⁡Asec⁡A\frac{\tan A}{\sec A}

  4. ((d))

     None of the above.

Show Answer
Answer: ((a))

cot A .cos A

12

A fruit vendor initially had a few apples. He sold 40% of them and still had 300 apples left. How many apples did he initially have?

  1. ((a))

    750

  2. ((b))

    450

  3. ((c))

    600

  4. ((d))

    500

Show Answer
Answer: ((a))

750

13

Megha bought a bag for ₹1,271 after getting an 18% discount on the marked price. Find the marked price of the bag.

  1. ((a))

    1,450

  2. ((b))

    1,650

  3. ((c))

    1,550

  4. ((d))

    1,350

Show Answer
Answer: ((a))

1,450

14

Which of the following methods is the safest method for disposal of toxic dust?

  1. ((a))

    Leaving it in the air for dilution.

  2. ((b))

    Sweeping it in open areas.

  3. ((c))

    Using special hazardous waste disposal containers.

  4. ((d))

    Putting it in regular trash cans.

Show Answer
Answer: ((a))

Leaving it in the air for dilution.

15

Vijay cycles 10 meters from home to tuition, then 5 meters to the shop. He returns home in the same way, covering the same distance. Find the total length of the path.

  1. ((a))

    20 m

  2. ((b))

    15 m

  3. ((c))

    Zero

  4. ((d))

    30 m

Show Answer
Answer: ((a))

20 m

16

A, B, C, D, E, and F live on six different floors of the same building. The ground floor is numbered 1, the floor immediately above it is numbered 2, and so on, until the topmost floor is numbered 6. D lives on an odd-numbered floor, but not 3. The sum of the floors on which D and E live is 7. A lives on the floor immediately below C. F lives on the topmost floor. How many people live between E and F?

  1. ((a))

    4

  2. ((b))

    1

  3. ((c))

    3

  4. ((d))

    2

Show Answer
Answer: ((a))

4

17

Which of the following noise levels is considered potentially harmful to human health when experienced over a long period of time?

  1. ((a))

    70 dB

  2. ((b))

    90 dB

  3. ((c))

    30 dB

  4. ((d))

    50 dB

Show Answer
Answer: ((a))

70 dB

18

Based on the English alphabetical order, three of the following four letter-cluster pairs are alike in a certain way and thus form a group. Which letter-cluster pair does not belong to that group? (Note: The odd letter-cluster pair is not based on the number of consonants/vowels or their position.)

  1. ((a))

     GN-PV

  2. ((b))

     JQ-SY

  3. ((c))

    HO-QW

  4. ((d))

    AH-JR

Show Answer
Answer: ((a))

 GN-PV

19

Which of the following relations is not correct?

  1. ((a))

    Electric power = (current)2 × resistance

  2. ((b))

    Electric power = voltage × current

  3. ((c))

    Electric power = voltage/current

  4. ((d))

    Electric power = (voltage)2 / resistance

Show Answer
Answer: ((a))

Electric power = (current)2 × resistance

20

In the following triplet, each group of letters is related to the next group following a certain logic. Select the option from the given ones that follows the same logic.

TERM-ERTM-TMRE

  1. ((a))

    WHEN-HWEN-WENH

  2. ((b))

    ZERO-EZRO-ZREO

  3. ((c))

    VICE-ICVE-VECI

  4. ((d))

    USER-RESU-REUS

Show Answer
Answer: ((a))

WHEN-HWEN-WENH

21

Which of the following options does not correctly represent the electric power P in a circuit (current, potential difference and resistance are symbolically written as I, V and R respectively.)

  1. ((a))

    P=V2RP = \frac{V^2}{R}

  2. ((b))

    P=I2RP = I^2 R

  3. ((c))

    P=VIP = VI

  4. ((d))

    P=IR2P = {IR^2}

Show Answer
Answer: ((a))

P=V2RP = \frac{V^2}{R}

22

In a certain code language, 'BARE' is coded as '8264' and 'RIDS' is coded as '3587'. What is the code for 'R' in the given code language?

  1. ((a))

    3

  2. ((b))

    8

  3. ((c))

    6

  4. ((d))

    5

Show Answer
Answer: ((a))

3

23

Kinetic energy and potential energy together are called which form of energy?

  1. ((a))

    Mechanical

  2. ((b))

    Chemical

  3. ((c))

    Ionic

  4. ((d))

    Nuclear

Show Answer
Answer: ((a))

Mechanical

24

If a circuit contains resistors of 10 Ω, 20 Ω and 60 Ω are connected in parallel, then find the total resistance of the circuit.

  1. ((a))

    90 Ω.

  2. ((b))

    60 Ω

  3. ((c))

    6 Ω

  4. ((d))

    20 Ω

Show Answer
Answer: ((a))

90 Ω.

25

What term is used to describe organisms in an ecosystem that produce their own food?

  1. ((a))

    Consumer

  2. ((b))

    Decomposer

  3. ((c))

    Vegetarian

  4. ((d))

    Producer

Show Answer
Answer: ((a))

Consumer

26

What should come in place of question mark (?) in the given series?

185 174 163 152 ? 130

  1. ((a))

    144

  2. ((b))

    142

  3. ((c))

    143

  4. ((d))

    141

Show Answer
Answer: ((a))

144

27

What is the primary source of energy for most ecosystems?

  1. ((a))

    Soil

  2. ((b))

    Wind

  3. ((c))

    Sunlight

  4. ((d))

    Water

Show Answer
Answer: ((a))

Soil

28

Potential energy falls under which of the following categories of energy?

  1. ((a))

    Thermal energy

  2. ((b))

    Light energy

  3. ((c))

    Chemical energy

  4. ((d))

    Mechanical energy

Show Answer
Answer: ((a))

Thermal energy

29

Two resistors of resistance 20 Ω and 30 Ω are connected in series in a circuit. If the supplied voltage is 250 V, find the current transmitted through the circuit.

  1. ((a))

    8 A

  2. ((b))

    12 A

  3. ((c))

    5 A

  4. ((d))

    20 A

Show Answer
Answer: ((a))

8 A

30

Study the given bar graph and answer the question below.

The given bar graph shows the number of flats sold by a builder in five different cities in the year 2020.

The number of flats sold in Delhi is what percent more than the number of flats sold in Mumbai?

  1. ((a))

    75%

  2. ((b))

    125%

  3. ((c))

    120%

  4. ((d))

    150%

Show Answer
Answer: ((a))

75%

31

Which of the following instruments is used to measure temperature?

  1. ((a))

    Hygrometer

  2. ((b))

    Voltmeter

  3. ((c))

    Thermometer

  4. ((d))

    Odometer

Show Answer
Answer: ((a))

Hygrometer

32

Use of energy efficient machinery in industrial settings mainly helps in ____________.

  1. ((a))

    increase energy consumption and consequently the cost of the product

  2. ((b))

    reducing industrial energy requirements and improve the competitiveness of products

  3. ((c))

    reducing operational efficiency

  4. ((d))

    extending the life of old equipment

Show Answer
Answer: ((a))

increase energy consumption and consequently the cost of the product

33

A dozen pairs of jeans costing ₹3,520 are available at a discount of 35%. How many pairs of jeans can be purchased for ₹572?

  1. ((a))

    2

  2. ((b))

    5

  3. ((c))

    1

  4. ((d))

    3

Show Answer
Answer: ((a))

2

34

Refer to the following letter and symbol series and answer the question that follows. Counting is to be done from left to right only. 

<br>

(Left) L R Ω Y A $ K ^ T J # Q & # E % S U * £ B (Right)

How many such symbols are there, each of which is immediately preceded by a vowel and also immediately followed by a letter?

  1. ((a))

    Two

  2. ((b))

    One

  3. ((c))

    Four

  4. ((d))

    Three

Show Answer
Answer: ((a))

Two

35

In the SI system, which of the following options best describes the fundamental quantities?

  1. ((a))

    Distance, Speed, Acceleration

  2. ((b))

    Temperature, pressure, volume

  3. ((c))

    Force, power, energy

  4. ((d))

    Length, mass, time

Show Answer
Answer: ((a))

Distance, Speed, Acceleration

36

An ammeter has 20 divisions between 0 and 2 A. The least count of an ammeter is _______________.

  1. ((a))

    0.2 A

  2. ((b))

    0.1 A

  3. ((c))

    1 A

  4. ((d))

    2 A

Show Answer
Answer: ((a))

0.2 A

37

If 'A' denotes '÷', 'B' denotes 'x', 'C' denotes '+' and 'D' denotes '-', then what will come in place of question mark (?) in the following equation?

38 C 32 A 4 D 5 B 7=?

  1. ((a))

    10

  2. ((b))

    8

  3. ((c))

    11

  4. ((d))

    9

Show Answer
Answer: ((a))

10

38

If x3+y3=16x^3 + y^3 = 16 and x + y = 4, then find the value of xy.

  1. ((a))

    4

  2. ((b))

    2

  3. ((c))

    3

  4. ((d))

    0

Show Answer
Answer: ((a))

4

39

What is the average human body temperature?

  1. ((a))

    40°C

  2. ((b))

    32°C

  3. ((c))

    42°C

  4. ((d))

    37°C

Show Answer
Answer: ((a))

40°C

40

Which of the following statements is true?

  1. ((a))

    In the kitchen, aluminium utensils are used because aluminium is a good conductor of heat.

  2. ((b))

    Both insulators and conductors allow heat to pass through them easily.

  3. ((c))

    Plastic is a good conductor of heat.

  4. ((d))

    Wood is a good conductor of heat.

Show Answer
Answer: ((a))

In the kitchen, aluminium utensils are used because aluminium is a good conductor of heat.

41

Refer to the following letter and symbol series and answer the question that follows. Counting is to be done from left to right only.

(Left) ^ T J # * £ B L R Ω Y # E % S U $ K Q & (Right)

How many such letters are there, each of which is immediately preceded by a letter and also immediately followed by a symbol?

  1. ((a))

    One

  2. ((b))

    Two

  3. ((c))

    Three

  4. ((d))

    Four

Show Answer
Answer: ((a))

One

42

According to the SI system of units, how many fundamental units are used to measure physical quantities?

  1. ((a))

    5

  2. ((b))

    10

  3. ((c))

    7

  4. ((d))

    4

Show Answer
Answer: ((a))

5

43

Eight people are sitting in two parallel rows containing 4 people in each row, in such a way that there is an equal distance between adjacent persons. Row 1 contains A, B, C and D, all of whom are facing south. Row 2 contains P, Q, R and S, all of whom are facing north. Thus, each person faces another person in the other row. Only two people sit between P and Q. A faces the person sitting to the immediate left of P. R sits to the immediate left of S. D sits to the immediate right of C. Who among the following faces P?

  1. ((a))

    D

  2. ((b))

    C

  3. ((c))

    B

  4. ((d))

    A

Show Answer
Answer: ((a))

D

44

Which of the following sequences of components primarily serves to execute instructions, store permanent firmware, temporarily store data during program execution, and provide a platform for interconnecting hardware components on a computer motherboard?

  1. ((a))

     RAM-ROM - CPU - PCB

  2. ((b))

     PCB-ROM-CPU-RAM

  3. ((c))

    CPU-RAM-ROM-PCB

  4. ((d))

    CPU-ROM-RAM- PCB

Show Answer
Answer: ((a))

 RAM-ROM - CPU - PCB

45

The area of ​​a regular polygon with side 12 cm is 144 cm². If the perpendicular distance from the center to the side of the polygon is 6 cm, find the number of sides of the polygon.

  1. ((a))

    5

  2. ((b))

    7

  3. ((c))

    6

  4. ((d))

    4

Show Answer
Answer: ((a))

5

46

A man purchased two varieties of pens at the rates of ₹8 for 9 pens and ₹8 per pen. If he purchased an equal number of pens of each of the two varieties and then sold all his pens at ₹6 per pen, what was his profit percentage?

  1. ((a))

    33%

  2. ((b))

    32%

  3. ((c))

    45%

  4. ((d))

    35%

Show Answer
Answer: ((a))

33%

47

Match the columns:

Engineering ApplicationsTypes of Engineering Drawings
A) Plans, facade elevations, and foundation drawings of houses to be constructed.P) Mechanical Engineering Drawings
B) Circuit Diagrams and Electrical Installation Drawings.Q) Electronics Engineering Drawings
C) PCB Track Drawings.R) Electrical Engineering Drawings
D) Riveted Joints and Welded Joints.S) Civil Engineering Drawings
  1. ((a))

     A-P: B-R; C-Q; D-S

  2. ((b))

     A-S; B-P; C-Q; D-R

  3. ((c))

    A-S; B-R; C-Q; D-P

  4. ((d))

    A-S; B-R; C-P; D-Q

Show Answer
Answer: ((a))

 A-P: B-R; C-Q; D-S

48

6 men or 5 women can complete a task in 7 days. 6 men work for 5 days and then leave. Find the number of women needed to complete the remaining task in 5 days.

  1. ((a))

    4

  2. ((b))

    2

  3. ((c))

    1

  4. ((d))

    3

Show Answer
Answer: ((a))

4

49

Which of the following statements are correct regarding the use of a fire extinguisher?

Statement 1: It is safe to attempt to extinguish any type of fire, regardless of the presence of toxic fumes.

Statement 2: The P.A.S.S. technique, which stands for Pull, Aim, Squeeze, and Sweep, is recommended for effective use of a fire extinguisher.

  1. ((a))

    Neither statement 1 nor 2 is correct.

  2. ((b))

    Only statement 1 is correct.

  3. ((c))

    Both statements 1 and 2 are correct.

  4. ((d))

    Only statement 2 is correct.

Show Answer
Answer: ((a))

Neither statement 1 nor 2 is correct.

50

Which of the following three-dimensional geometric figures has eight vertices and six rectangular faces?

  1. ((a))

    Pyramid

  2. ((b))

    Cylinder

  3. ((c))

    Parallelogram

  4. ((d))

    Cuboid

Show Answer
Answer: ((a))

Pyramid

51

In a hospital, the ratio between the number of doctors and the number of nurses was 1 : 3. The addition of 12 new doctors and the departure of 24 nurses brings the ratio to 3 : 4. After k more nurses resign from the hospital, the ratio becomes 1 : 1. Find the value of k.

  1. ((a))

    12

  2. ((b))

    28

  3. ((c))

    24

  4. ((d))

    26

Show Answer
Answer: ((a))

12

52

Which of the following statements is/are correct regarding functional dimension (F) in engineering drawings?

Statement 1: Functional dimensions are essential for the function of the component or space.

Statement 2: Functional dimensions are usually shown without any boundaries.

Statement 3: Functional dimensions are shown for reference purposes only.

  1. ((a))

    Only statement 1 is true

  2. ((b))

    Only statement 3 is true

  3. ((c))

    Only statements 2 and 3 are true

  4. ((d))

    Only statements 1 and 2 are true

Show Answer
Answer: ((a))

Only statement 1 is true

53

Read the given statements and conclusions carefully. Assuming that the information given in the statements is true, even if it appears to be at variance from commonly known facts, decide which of the given conclusions logically follows from the given statements.

Statements:

  1. Some desks are tables.

II. All tables are cabinets.

III. All cabinets are beds.

Conclusions:

I. Some beds are tables.

II. All cabinets are desks.

  1. ((a))

    Only conclusion I follows.

  2. ((b))

    Only conclusion II follows.

  3. ((c))

    Both conclusions I and II follow.

  4. ((d))

    Neither conclusion I nor conclusion II follows.

Show Answer
Answer: ((a))

Only conclusion I follows.

54

Ganpat starts from point A and walks 18 m west. He turns left, walks 32 m, then turns left again, walks 26 m, then turns left again, walks 61 m, and stops at point B. Meena starts from point Z, which is 22 m east of point A. She walks 42 m north, turns right, walks 35 m, turns right and walks 13 m, and stops at point Y. Find the shortest distance between point B and point Y. (All turns are 90-degree turns only.)

  1. ((a))

    52 m

  2. ((b))

    43 m

  3. ((c))

    57 m

  4. ((d))

    49 m

Show Answer
Answer: ((a))

52 m

55

Three circular plates of radii 3 m, 2 m, and 1 m are cut from a rectangular cardboard sheet 46 m long and 8 m wide. If the area of ​​the remaining cardboard sheet is equal to the area of ​​a square, find the length of each side of the square. (Use π=227\pi = \frac{22}{7})

  1. ((a))

    20 m

  2. ((b))

    18 m

  3. ((c))

    14 m

  4. ((d))

    16 m

Show Answer
Answer: ((a))

20 m

56

In a certain code language, 'CARD' is coded as '8674' and 'MICE' is coded as '3517'. What is the code for 'C' in the given code language?

  1. ((a))

    8

  2. ((b))

    7

  3. ((c))

    1

  4. ((d))

    6

Show Answer
Answer: ((a))

8

57

When an object of mass 50 kg is moved from one point to another along a horizontal line, what is the work done by the force of gravity on the object? (g=10m/s2)(g = 10 m / s ^ 2)

  1. ((a))

    Zero

  2. ((b))

    50 J

  3. ((c))

    500 J

  4. ((d))

    -500 J

Show Answer
Answer: ((a))

Zero

58

If 50 : x :: x : 32 and x > 0, then find the value of x.

  1. ((a))

    45.8

  2. ((b))

    40

  3. ((c))

    38.7

  4. ((d))

    40.6

Show Answer
Answer: ((a))

45.8

59

Two plumbers, X and Y, are paid a total of ₹770 per day by their employer. If X is paid 140% of the amount paid to Y, how much is Y paid per day (in ₹, rounded to two decimal places)?

  1. ((a))

    320.83

  2. ((b))

    220.83

  3. ((c))

    270.83

  4. ((d))

    370.83

Show Answer
Answer: ((a))

320.83

60

What will be the value of 10 km/hr in SI units?

  1. ((a))

    10 m/s

  2. ((b))

    0.16 m/s

  3. ((c))

    2.7 m/s

  4. ((d))

    1000 m/s

Show Answer
Answer: ((a))

10 m/s

61

In a certain code language,  

<br>

'A + B' means 'A is the mother of B',

'A - B' means 'A is the brother of B',

'A × B' means 'A is the wife of B' and

'A & B' means 'A is the father of B'.

<br>

If 'E & F + G - H x T', then how is E related to T?

  1. ((a))

    Wife's mother's father

  2. ((b))

    Wife's brother

  3. ((c))

    Wife's father

  4. ((d))

    Wife's mother's brother

Show Answer
Answer: ((a))

Wife's mother's father

62

If x = (7 + √5), y = (7 - √5), then find the value of x² + y².

  1. ((a))

    96

  2. ((b))

    137

  3. ((c))

    124

  4. ((d))

    108

Show Answer
Answer: ((a))

96

63

Convert 1 kilowatt hour (kWh) to joule.

  1. ((a))

    1 kWh=3.6×106 J{1\ \text{kWh} = 3.6 \times 10^6\ \text{J}}

  2. ((b))

    1 kWh=3.6×107 J1\ \text{kWh} = 3.6 \times 10^7\ \text{J}

  3. ((c))

    1 kWh=3.6×105 J1\ \text{kWh} = 3.6 \times 10^5\ \text{J}

  4. ((d))

    1 kWh=3.6×103 J1\ \text{kWh} = 3.6 \times 10^3\ {J}

Show Answer
Answer: ((a))

1 kWh=3.6×106 J{1\ \text{kWh} = 3.6 \times 10^6\ \text{J}}

64

Which of the following letter-clusters should replace # and % so that the pattern and relationship followed between the letter-cluster pairs 4 to the left of :: is the same as the pattern and relationship followed between the letter-cluster pairs 4 to the right of ::?

: HDI :: MIN : %

  1. ((a))

    = JFI, % = KGL

  2. ((b))

     # = JFK, % = KGM

  3. ((c))

     # = JFK, % = KGL

  4. ((d))

    = JFK, % = KHL

Show Answer
Answer: ((a))

= JFI, % = KGL

65

What is the designation of the trimmed sheet with dimensions 297 mm x 420 mm, as per the ISO-A size series?

  1. ((a))

    A1

  2. ((b))

    A2

  3. ((c))

    A4

  4. ((d))

    A3

Show Answer
Answer: ((a))

A1

66

Which of the following expressions is not correct for electric power?

  1. ((a))

    P = VI

  2. ((b))

    P= V2/R

  3. ((c))

    P = I2/R

  4. ((d))

    P = I2R

Show Answer
Answer: ((a))

P = VI

67

What does the symbol given below in the circuit diagram represent?

  1. ((a))

    Voltmeter

  2. ((b))

    Voltage source

  3. ((c))

    Resistor

  4. ((d))

    Variable resistor

Show Answer
Answer: ((a))

Voltmeter

68

Preeti, Kiran, Grace, Ankit, Deepak, Nitin and Neelam each have an exam on a different day of the same week, starting from Monday and ending on Sunday. Preeti has an exam on Thursday. Only one person has an exam between Preeti and Nitin. Grace has an exam the day immediately before Nitin but not on Monday. Only two people have an exam between Grace and Deepak. Neelam has her exam before Ankit but after Kiran. Who among the following has an exam on Monday?

  1. ((a))

    Nitin

  2. ((b))

    Neelam 

  3. ((c))

    Kiran

  4. ((d))

    Deepak

Show Answer
Answer: ((a))

Nitin

69

If 59\frac{5}{9} of a number is 6 more than 12\frac{1}{2} of that number, then find that number.

  1. ((a))

    104

  2. ((b))

    108

  3. ((c))

    106

  4. ((d))

    102

Show Answer
Answer: ((a))

104

70

What should be done immediately after a fuel spillage in a workshop?

  1. ((a))

    Cover it with plastic to prevent evaporation.

  2. ((b))

    Use water to wash it off

  3. ((c))

    Leave it as is and inform the supervisor later

  4. ((d))

    Empty the area and control overflow using absorbent materials

Show Answer
Answer: ((a))

Cover it with plastic to prevent evaporation.

71

A cube of mass 5.74 g occupies a volume of 1.2 cm³. The density (in g/cm³) expressed with the correct number of significant figures is _____________.

  1. ((a))

    4.7833

  2. ((b))

    4.8

  3. ((c))

    4.78

  4. ((d))

    4.783

Show Answer
Answer: ((a))

4.7833

72

In science, work done is defined as:

  1. ((a))

    force / distance

  2. ((b))

    force / displacement

  3. ((c))

    force × displacement

  4. ((d))

    force × distance

Show Answer
Answer: ((a))

force / distance

73

Simplify 976 × 265 + 976 × 735.

  1. ((a))

    752800

  2. ((b))

    976000

  3. ((c))

    658200

  4. ((d))

    876000

Show Answer
Answer: ((a))

752800

74

Which of the following is not an advantage of using mobile governance using ICT?

  1. ((a))

    Reduced costs for the government

  2. ((b))

    Better access to government services for citizens

  3. ((c))

    Increased transparency and accountability in government

  4. ((d))

    Increasing the efficiency of government processes

Show Answer
Answer: ((a))

Reduced costs for the government

75

Study the given diagram carefully and answer the question given below. The numbers in different sections represent the number of children who like different desserts.

<br> <br>

How many children like both pastries and ice cream but not chocolate?

  1. ((a))

    9

  2. ((b))

    6

  3. ((c))

    7

  4. ((d))

    8

Show Answer
Answer: ((a))

9

76

The rate of doing work is known as ___________.

  1. ((a))

    Power

  2. ((b))

    Force

  3. ((c))

    Kinetic energy

  4. ((d))

    Potential energy

Show Answer
Answer: ((a))

Power

77

Which of the following actions help prevent injuries from slips and falls?

  1. ((a))

    Wearing loose shoes for comfort

  2. ((b))

    Walk carefully on wet floors

  3. ((c))

    Cleaning up spills immediately and using warning signs

  4. ((d))

    Ignoring clutter on the sidewalk

Show Answer
Answer: ((a))

Wearing loose shoes for comfort

78

In the following series, only one letter-cluster is wrong. Choose the wrong letter-cluster.

PCO MEM JGK GIJ DKG AME

  1. ((a))

    AME

  2. ((b))

    JGK

  3. ((c))

    DKG

  4. ((d))

    GIJ

Show Answer
Answer: ((a))

AME

79

Which of the following statements about geometric shapes is/are true?

  1. Geometric shapes are enclosed figures formed by joining two or more points, lines, or curves.
  2. Geometric shapes are always open-ended and made up of only straight lines.
  1. ((a))

    Only statement 1 is true

  2. ((b))

    Only statement 2 is true

  3. ((c))

    Both statements 1 and 2 are true

  4. ((d))

    Neither statement 1 nor 2 is true

Show Answer
Answer: ((a))

Only statement 1 is true

80

A tank has two inlets, I1 and I2. I1 alone can fill it in 8 hours, and I2 alone can fill it in 4 hours. If both inlets are open, how long will it take to fill the tank?

  1. ((a))

    2 hours

  2. ((b))

    2232\frac{2}{3} hours

  3. ((c))

    3233\frac{2}{3} hours

  4. ((d))

    4234\frac{2}{3} hours

Show Answer
Answer: ((a))

2 hours

81

A 280 m long train travelling at a speed of 72 km/hr crosses a platform in 30 seconds. Find the length (in m) of the platform.

  1. ((a))

    335

  2. ((b))

    280

  3. ((c))

    300

  4. ((d))

    320

Show Answer
Answer: ((a))

335

82

Amit's income in 2019 was ₹27,000. His income increases by 10% each year. What was his income (in ₹) in 2021?

  1. ((a))

    32,400

  2. ((b))

    29,700

  3. ((c))

    32,670

  4. ((d))

    27,000

Show Answer
Answer: ((a))

32,400

83

Which of the following is the best way to identify hazards at the workplace?

  1. ((a))

    Waiting for an event to occur

  2. ((b))

    Performing regular safety inspections

  3. ((c))

    Relying on employees to report accidents

  4. ((d))

    Ignoring small risks

Show Answer
Answer: ((a))

Waiting for an event to occur

84

Given below are two sets of numbers. In each set, performing certain mathematical operations on the first number gives the second number. Similarly, performing certain mathematical operations on the second number gives the third number, and so on. Which of the given options follows the same set of operations as the given sets?

<br>

(Note: Operations must be performed on whole numbers without breaking the numbers into their component digits. For example, take 13. Operations such as addition, subtraction, multiplication, etc. can be performed on 13. Breaking 13 into 1 and 3 and then performing mathematical operations on 1 and 3 is not permitted.)

<br>

3-9-12-24; 4-16-20-40

  1. ((a))

    9-2-11-24

  2. ((b))

    1-1-2-4

  3. ((c))

    6-12-18-34

  4. ((d))

    7-49-56-122

Show Answer
Answer: ((a))

9-2-11-24

85

Which of the following will verify the credentials and documents of applicants uploaded on the National Scholarship Portal?

  1. ((a))

    National Scholarship Portal

  2. ((b))

    The University/Institute in which the applicant is studying.

  3. ((c))

    Third Party

  4. ((d))

    Government

Show Answer
Answer: ((a))

National Scholarship Portal

86

The average of three numbers is 20. If two numbers are 16 and 24, find the third number.

  1. ((a))

    22

  2. ((b))

    21

  3. ((c))

    20

  4. ((d))

    19

Show Answer
Answer: ((a))

22

87

Which of the following statements is/are true?

Statement 1: Heat conductors allow heat to pass through them easily.

Statement 2: All plastics are good conductors of heat.

  1. ((a))

    Only statement 1

  2. ((b))

    Only statement 2

  3. ((c))

    Neither statement 1 nor statement 2

  4. ((d))

    Both statement 1 and statement 2

Show Answer
Answer: ((a))

Only statement 1

88

In the following number-pairs, the second number is obtained by performing certain mathematical operations on the first number. What number should be replaced by X and Y so that the pattern followed by the two numbers to the left of :: is the same as the pattern followed by the two numbers to the right of ::?

(Note: Operations must be performed on whole numbers, without breaking the numbers into their component digits. For example, take 13. Operations such as addition/subtraction/multiplication can be performed on 13. Breaking 13 into 1 and 3 and then performing mathematical operations on 1 and 3 is not permitted.)

X: 85 :: 36: Y

  1. ((a))

    x = 44, Y = 73

  2. ((b))

     x = 42, Y = 73

  3. ((c))

     x = 43, Y = 77

  4. ((d))

     x = 42, Y = 71

Show Answer
Answer: ((a))

x = 44, Y = 73

89

Jaspreet deposited ₹58,550 at 20% annual interest rate compounded annually. What is the total amount (in ₹) Jaspreet will receive after 2 years ?

  1. ((a))

    84,700

  2. ((b))

    84,312

  3. ((c))

    84,735

  4. ((d))

    83,876

Show Answer
Answer: ((a))

84,700

90

Rinku travels 136 meters in his car in 17 seconds. Find his speed (in km/hr).

  1. ((a))

    11.6

  2. ((b))

    17

  3. ((c))

    28.8

  4. ((d))

    26

Show Answer
Answer: ((a))

11.6

91

What should come in place of question mark (?) in the given series?

893 891 889 887 ? 883

  1. ((a))

    986

  2. ((b))

    885

  3. ((c))

    985

  4. ((d))

    886

Show Answer
Answer: ((a))

986

92

Ten people are sitting in two parallel rows, five in each row, in such a way that there is an equal distance between adjacent persons.

Row I contains A, B, C, D, and E, all of whom are facing south. Row II contains R, S, T, U and V, all of whom are facing north. Thus, each person faces a person from the other row. A sits at the right end of his row and faces U. R sits in the middle of his row and faces C. E sits between C and D, facing T. S sits at the right end of his row.

Who sits exactly opposite B?

  1. ((a))

    T

  2. ((b))

    R

  3. ((c))

    U

  4. ((d))

    V

Show Answer
Answer: ((a))

T

93

What type of thermometer is used to measure the internal temperature of ice?

  1. ((a))

    Digital thermometer

  2. ((b))

    Clinical thermometer

  3. ((c))

    Infrared thermometer

  4. ((d))

    Laboratory Thermometer

Show Answer
Answer: ((a))

Digital thermometer

94

An ammeter with a range of 0 to 10 A reads a current of 7.5 A. If its actual value is 6.2 A, the relative error is ________.

  1. ((a))

    13%

  2. ((b))

    17.33%

  3. ((c))

    20.96%

  4. ((d))

    4.8%

Show Answer
Answer: ((a))

13%

95

The average of 5 results is 51 and the average of the first 4 of them is 50. The 5th result is.

  1. ((a))

    55

  2. ((b))

    50

  3. ((c))

    51

  4. ((d))

    54

Show Answer
Answer: ((a))

55

96

A copper spoon is dipped in hot water. What happens to the other end?

  1. ((a))

    It gets heated by conduction.

  2. ((b))

    It cools down by conduction.

  3. ((c))

    It gets heated by convection.

  4. ((d))

    It cools down by convection.

Show Answer
Answer: ((a))

It gets heated by conduction.

97

Based on the English alphabetical order, three of the following four letter-clusters are alike in a certain way and thus form a group. Which of the given letter-clusters does not belong to that group? (Note: The odd letter-cluster is not based on the number of consonants/vowels or their position in the letter-cluster.)

  1. ((a))

    GMOT

  2. ((b))

    FLNS

  3. ((c))

    NTVB

  4. ((d))

    LRTY

Show Answer
Answer: ((a))

GMOT

98

A rod of length 89\frac{8}{9} meters breaks into two pieces. If one piece is 13\frac{1}{3} meters long, find the length (in m) of the other piece.

  1. ((a))

    29\frac{2}{9}

  2. ((b))

    79\frac{7}{9}

  3. ((c))

    59\frac{5}{9}

  4. ((d))

    49\frac{4}{9}

Show Answer
Answer: ((a))

29\frac{2}{9}

99

Four 4-ohm resistors are connected in parallel. These four parallel resistors are then connected in series with a 9-ohm resistor. Find the equivalent resistance.

  1. ((a))

    10 ohm 

  2. ((b))

    2 ohm 

  3. ((c))

    3 ohm 

  4. ((d))

    1  ओम

Show Answer
Answer: ((a))

10 ohm 

100

An object weighs 60 N on Earth. What will be its weight on the surface of the Moon?

  1. ((a))

    600 N

  2. ((b))

    10 N

  3. ((c))

    6 N

  4. ((d))

    60 N

Show Answer
Answer: ((a))

600 N

Part B (75 questions)

101

The key difference between a marking gauge and a mortise gauge is:

  1. ((a))

    method of adjustment

  2. ((b))

    size of the tool

  3. ((c))

    material of construction

  4. ((d))

    number of scribing pins

Show Answer
Answer: ((a))

method of adjustment

102

According to BIS SP 46-2003, which of the following applications is correctly represented by a chain-thin line in engineering drawings?

  1. ((a))

    Hidden edges

  2. ((b))

    Center lines

  3. ((c))

    Visible edges

  4. ((d))

    Dimension lines

Show Answer
Answer: ((a))

Hidden edges

103

What is the difference between a bevel gauge and a bevel protractor?

  1. ((a))

    There is no difference; both tools are the same.

  2. ((b))

    A bevel protractor is used for depth measurement, while a bevel gauge is used for height measurement.

  3. ((c))

    A bevel gauge is fixed, while a bevel protractor is adjustable.

  4. ((d))

    A bevel gauge is adjustable, while a bevel protractor provides precise angular measurements.

Show Answer
Answer: ((a))

There is no difference; both tools are the same.

104

Match the following terminologies in riveted joint with their corresponding meanings.

Column IColumn II
Pitch (A)distance between centres of adjoining rivets in the same row (P)
Margin (B)distance between an edge of the plate and the nearest rivet-hole (Q)
Lap joint (C)plates to be connected overlap each other (R)
Row pitch (D)distance between the rows of rivets (S)
  1. ((a))

    A-S, B-P, C-Q, D-R

  2. ((b))

    A-S, B-R, C-Q, D-P

  3. ((c))

    A-P, B-R, C-Q, D-S

  4. ((d))

    A-P, B-Q, C-R, D-S

Show Answer
Answer: ((a))

A-S, B-P, C-Q, D-R

105

Which of the following hand-operated drilling machines is used for drilling small diameter holes up to 6 mm?

  1. ((a))

    Breast drilling machine

  2. ((b))

    Bevel gear type drilling machine

  3. ((c))

    Ratchet drilling machine

  4. ((d))

    Electric hand drill

Show Answer
Answer: ((a))

Breast drilling machine

106

Generally, the maximum efficiency of a diesel engine depends on:

  1. ((a))

    Temperature and pressure

  2. ((b))

    Density and viscosity

  3. ((c))

    Heat transfer and friction

  4. ((d))

    Speed and load

Show Answer
Answer: ((a))

Temperature and pressure

107

Which of the following parts of a file is the part fitted to the tang for holding the file?

  1. ((a))

    Tang 

  2. ((b))

    Tip or Point

  3. ((c))

    Handle

  4. ((d))

    Edge

Show Answer
Answer: ((a))

Tang 

108

The schedule number of a pipe is an indicator of which property?

  1. ((a))

    Wall Thickness

  2. ((b))

    Inner Diameter

  3. ((c))

    Outer Diameter

  4. ((d))

    Material Composition

Show Answer
Answer: ((a))

Wall Thickness

109

When two pulleys are more than 8 metres apart, then which of the following belt drives is used for power transmission?

  1. ((a))

    Light drive

  2. ((b))

    Flat belt

  3. ((c))

    V-belt

  4. ((d))

    Circular belt

Show Answer
Answer: ((a))

Light drive

110

Which of the following files is used for filing narrow grooves and angles above 10°?

  1. ((a))

    Half round file

  2. ((b))

    Triangular file

  3. ((c))

    Square file

  4. ((d))

    Knife-edge file

Show Answer
Answer: ((a))

Half round file

111

If the basic size of the diameter of a shaft is 75 mm and variation limit of +0.02 mm is given, then its tolerance in mm is:

  1. ((a))

    +0.02

  2. ((b))

    +0.04

  3. ((c))

    −0.04

  4. ((d))

    −0.02

Show Answer
Answer: ((a))

+0.02

112

The type of workpieces that can be successfully held in a 4-jaw chuck, and might be difficult to hold in a 3-jaw chuck, are:

  1. ((a))

    irregular or eccentric workpieces

  2. ((b))

    only small diameter workpieces

  3. ((c))

    only hexagonal workpieces

  4. ((d))

    only round workpieces

Show Answer
Answer: ((a))

irregular or eccentric workpieces

113

What is single-riveted lap joint?

  1. ((a))

    Joint made with three row of rivets

  2. ((b))

    Joint made with four row of rivets

  3. ((c))

    Joint made with two row of rivets

  4. ((d))

    Joint made with only one row of rivets

Show Answer
Answer: ((a))

Joint made with three row of rivets

114

What does the given surface finish symbol represent? 

  1. ((a))

    The surface should be finished using grinding only.

  2. ((b))

    Special machining characteristics must be specified.

  3. ((c))

    Machining must be performed to remove material.

  4. ((d))

    Material removal is not allowed on this surface.

Show Answer
Answer: ((a))

The surface should be finished using grinding only.

115

An electronic digital caliper displays the measurement on a _____.

  1. ((a))

    dial gauge

  2. ((b))

    liquid crystal display screen 

  3. ((c))

    mechanical counter

  4. ((d))

    Vernier scale

Show Answer
Answer: ((a))

dial gauge

116

When selecting a sheet size for an original drawing, what should be the primary consideration?

  1. ((a))

    The size of the reproduction.

  2. ((b))

    The clarity and resolution required.

  3. ((c))

    The orientation of the drawing (horizontal or vertical).

  4. ((d))

    The standard size of the drawing office.

Show Answer
Answer: ((a))

The size of the reproduction.

117

Identify the rough file grade from the figures given below.

  1. ((a))

    (c) 

  2. ((b))

    (b) 

  3. ((c))

    (a) 

  4. ((d))

    (d) 

Show Answer
Answer: ((a))

(c) 

118

________ strategy is best suited for critical equipment that cannot afford unexpected downtime. 

  1. ((a))

    Reactive maintenance

  2. ((b))

    Run-to-failure maintenance

  3. ((c))

    Predictive maintenance

  4. ((d))

    Preventive maintenance

Show Answer
Answer: ((a))

Reactive maintenance

119

What type of surfaces can a telescopic gauge measure?

  1. ((a))

    Only external cylindrical surfaces

  2. ((b))

    Only deep holes

  3. ((c))

    Only circular bores

  4. ((d))

    Both circular and irregular bores

Show Answer
Answer: ((a))

Only external cylindrical surfaces

120

A circuit consists of three resistors; 15 ohms, 10 ohms, and 20 ohms. The 15-ohm resistor is in series with the parallel combination of the 10-ohm and 20-ohm resistors. If a 24 V battery is applied across the circuit, what is the total current flowing through the circuit?

  1. ((a))

    3.1 A

  2. ((b))

    2.1 A

  3. ((c))

    1.1 A

  4. ((d))

    0.1 A

Show Answer
Answer: ((a))

3.1 A

121

Which type of hydraulic cylinder is commonly used when a long stroke is required in a compact design?

  1. ((a))

    Double-acting cylinder

  2. ((b))

    Single-acting cylinder

  3. ((c))

    Rotary actuator

  4. ((d))

    Telescopic cylinder

Show Answer
Answer: ((a))

Double-acting cylinder

122

Which of the following advantages of chain drive over belt drive is INCORRECT?

  1. ((a))

    The production cost of chains is relatively high.

  2. ((b))

    It gives less load on the shafts.

  3. ((c))

    It may be used for both long as well as short distances.

  4. ((d))

    It gives a high transmission efficiency.

Show Answer
Answer: ((a))

The production cost of chains is relatively high.

123

What is the unit of specifying slip gauges?

  1. ((a))

    Millimetres

  2. ((b))

    Kilograms

  3. ((c))

    Newtons

  4. ((d))

    Kilometres

Show Answer
Answer: ((a))

Millimetres

124

Arrange the following steps in the correct order to draw an equilateral triangle with each side of 35 mm.

  1. Join CA and CB.
  2. Draw a line and mark AB 35 mm as the side of the triangle.
  3. With radius AB and center A and B, draw arcs cutting at C.
  4. ABC is the required triangle.
  1. ((a))

    1, 2, 4, 3

  2. ((b))

    2, 3, 1, 4

  3. ((c))

    2, 1, 3, 4

  4. ((d))

    3, 2, 1, 4

Show Answer
Answer: ((a))

1, 2, 4, 3

125

The process of ________ involves using a cutting tool called a tap to sever internal threads in a hole.

  1. ((a))

    knurling

  2. ((b))

    facing

  3. ((c))

    chamfering

  4. ((d))

    tapping

Show Answer
Answer: ((a))

knurling

126

In a lead-acid battery, what is the chemical composition of the material used for the positive plate during discharge? 

  1. ((a))

    Lead sulfate (PbSO₄) 

  2. ((b))

    Sulphuric acid (H₂SO₄)

  3. ((c))

    Lead (Pb)

  4. ((d))

    Lead dioxide (PbO₂)

Show Answer
Answer: ((a))

Lead sulfate (PbSO₄) 

127

Which of the following vices consists of a handle and a small collet chuck at one end?

  1. ((a))

    Hand vice

  2. ((b))

    Pin vice

  3. ((c))

    Pipe vice

  4. ((d))

    Toolmaker’s vice

Show Answer
Answer: ((a))

Hand vice

128

Which of the following is NOT required for estimating materials in preventive maintenance?

  1. ((a))

    Equipment maintenance history

  2. ((b))

    Supplier availability of spare parts

  3. ((c))

    Standard life expectancy of components

  4. ((d))

    Power consumption of the machine

Show Answer
Answer: ((a))

Equipment maintenance history

129

For what purpose are pins and clips used in engineering drawings?

  1. ((a))

    To transfer dimensions and dividing lines into a number of equal parts

  2. ((b))

    To draw horizontal lines, parallel lines and to guide/hold the set squares

  3. ((c))

    To fasten the drawing sheet on to the drawing board firmly so that it does not shake 

  4. ((d))

    To support the drawing paper/tracing paper for making drawing

Show Answer
Answer: ((a))

To transfer dimensions and dividing lines into a number of equal parts

130

What is Pascal’s Law that is fundamental to hydraulic systems?

  1. ((a))

    Force is inversely proportional to pressure.

  2. ((b))

    Pressure in a confined fluid is constant at all points.

  3. ((c))

    Fluid velocity is directly proportional to the cross-sectional area.

  4. ((d))

    Energy cannot be created or destroyed in a hydraulic system.

Show Answer
Answer: ((a))

Force is inversely proportional to pressure.

131

Which of the following types of thread is usually found on the machine spindle?

  1. ((a))

    Knuckle thread

  2. ((b))

    Buttress thread

  3. ((c))

    Unified standard thread

  4. ((d))

    Square thread

Show Answer
Answer: ((a))

Knuckle thread

132

What is the purpose of an emergency evacuation plan?

  1. ((a))

    To increase productivity

  2. ((b))

    To ensure safe and orderly evacuation during emergencies

  3. ((c))

    To allow workers to leave early

  4. ((d))

    To avoid safety drills

Show Answer
Answer: ((a))

To increase productivity

133

What is the primary reason for electrical injuries when a person comes in contact with electrical equipment?

  1. ((a))

    Devices are used for too long.

  2. ((b))

    Current flows through the body causing harm.

  3. ((c))

    Electrical devices are too powerful.

  4. ((d))

    Electrical equipment is not properly grounded.

Show Answer
Answer: ((a))

Devices are used for too long.

134

Why is it important for every person to follow safety procedures in the workplace?

  1. ((a))

    To increase overall production efficiency

  2. ((b))

    To limit the need for frequent supervision

  3. ((c))

    To minimise risks and avoid accidents

  4. ((d))

    To reduce operational costs significantly

Show Answer
Answer: ((a))

To increase overall production efficiency

135

A/An ________ is provided to keep the micrometer fixed so that the reading can be done easily and without any difficulty.

  1. ((a))

    lock nut

  2. ((b))

    sleeve or barrel

  3. ((c))

    anvil

  4. ((d))

    thimble

Show Answer
Answer: ((a))

lock nut

136

A circular hole of radius 3 cm is cut from a rectangular sheet of dimensions 12 cm × 10 cm. Find the remaining area. (Take π = 3.14) 

  1. ((a))

    100 cm²

  2. ((b))

    75.74 cm² 

  3. ((c))

    95.86 cm²

  4. ((d))

    91.74 cm²

Show Answer
Answer: ((a))

100 cm²

137

When measuring the resistance of a resistor using an ohmmeter, what does a reading of zero resistance indicate?

  1. ((a))

    The resistor is open-circuited.

  2. ((b))

    The resistor is short-circuited.

  3. ((c))

    The ohmmeter is malfunctioning.

  4. ((d))

    The resistor is functioning normally.

Show Answer
Answer: ((a))

The resistor is open-circuited.

138

If sin θ=35\mathrm{sin~\theta = \frac{3}{5}} find cos θ\mathrm{cos~\theta}.

  1. ((a))

    34\frac{3}{4}

  2. ((b))

    54\frac{5}{4}

  3. ((c))

    35\frac{3}{5}

  4. ((d))

    45\frac{4}{5}

Show Answer
Answer: ((a))

34\frac{3}{4}

139

Which of the following is a key characteristic of a low-pressure blowpipe/torch in welding? 

  1. ((a))

    It requires an external pump to supply acetylene gas.

  2. ((b))

    It directly mixes acetylene and oxygen in equal proportions.

  3. ((c))

    It uses high-pressure oxygen to create a vacuum for acetylene suction.

  4. ((d))

    It operates only with high-pressure acetylene cylinders.

Show Answer
Answer: ((a))

It requires an external pump to supply acetylene gas.

140

Which component is essential in a single-acting cylinder to facilitate the return stroke?

  1. ((a))

    Double inlet valve

  2. ((b))

    Spring or external load

  3. ((c))

    Pressure relief valve 

  4. ((d))

    Flow control valve

Show Answer
Answer: ((a))

Double inlet valve

141

_________ type of preventive maintenance is performed based on actual machine condition rather than a fixed schedule.

  1. ((a))

    Condition-based maintenance

  2. ((b))

    Time-based maintenance

  3. ((c))

    Breakdown maintenance

  4. ((d))

    Run-to-Failure maintenance

Show Answer
Answer: ((a))

Condition-based maintenance

142

What is the advantage of giving heat treatment to a material? 

  1. ((a))

    To decrease the melting point of the material

  2. ((b))

    To increase the weight of the material

  3. ((c))

    To change it from one element to another element 

  4. ((d))

    To make surgical knives of sharp edges

Show Answer
Answer: ((a))

To decrease the melting point of the material

143

Which characteristic of cellulosic electrodes makes them unsuitable for high-strength steels?

  1. ((a))

    They have a very thin coating, causing rapid wear.

  2. ((b))

    They create excessive slag, leading to contamination.

  3. ((c))

    They operate only on a low-voltage DC supply.

  4. ((d))

    They produce high levels of hydrogen in the weld.

Show Answer
Answer: ((a))

They have a very thin coating, causing rapid wear.

144

The terms _____ and _____ refer to the greatest and smallest variance, respectively, specified on a fundamental size or nominal measurement.

  1. ((a))

    limit; fit

  2. ((b))

    jig; fixture

  3. ((c))

    low limit; high limit

  4. ((d))

    high limit; low limit

Show Answer
Answer: ((a))

limit; fit

145

Threading is an operation of cutting __________ on the external cylindrical surface of the job. 

  1. ((a))

    helical grooves

  2. ((b))

    v-shaped grooves

  3. ((c))

    rectangular grooves

  4. ((d))

    circular grooves

Show Answer
Answer: ((a))

helical grooves

146

What is the value of (38)+(512)(\frac{3}{8})+(\frac{5}{12})

  1. ((a))

    820\frac{8}{20}

  2. ((b))

    1724\frac{17}{24}

  3. ((c))

    712\frac{7}{12}

  4. ((d))

    1924\frac{19}{24}

Show Answer
Answer: ((a))

820\frac{8}{20}

147

In Lathe Machine operation, the act of making plain ends of a job in their actual length is called ___________. 

  1. ((a))

    facing

  2. ((b))

    knurling

  3. ((c))

    step turning

  4. ((d))

    chamfering

Show Answer
Answer: ((a))

facing

148

 ___________ microstructure is typically obtained after normalising low-carbon steel. 

  1. ((a))

    Pearlite and ferrite

  2. ((b))

    Austenite

  3. ((c))

    Bainite

  4. ((d))

    Martensite

Show Answer
Answer: ((a))

Pearlite and ferrite

149

The term ______ refers to the limit of variation allowed on either side of the correct dimension to provide the job property of interchangeability (in mass production of part). 

  1. ((a))

    high limit 

  2. ((b))

    fit

  3. ((c))

    tolerance

  4. ((d))

    low limit

Show Answer
Answer: ((a))

high limit 

150

The purpose of providing a side relief angle of 1° to 2° on a grooving tool is to:

  1. ((a))

    improve the surface finish

  2. ((b))

    prevent rubbing against the sides of the groove

  3. ((c))

    increase the cutting speed

  4. ((d))

    reduce the cutting force

Show Answer
Answer: ((a))

improve the surface finish

151

In thread cutting, 'BSW' stands for _________________. 

  1. ((a))

    British Standard Weight

  2. ((b))

    Bharath Standard Whitworth

  3. ((c))

    British Stationary Whitworth

  4. ((d))

    British Standard Whitworth

Show Answer
Answer: ((a))

British Standard Weight

152

Which of the following organisations is responsible for enforcing workplace safety regulations in India?

  1. ((a))

    World Health Organization (WHO)

  2. ((b))

    Food and Drug Administration (FDA)

  3. ((c))

    Directorate General of Factory Advice Service and Labour Institutes (DGFASLI)

  4. ((d))

    Environmental Protection Agency (EPA) 

Show Answer
Answer: ((a))

World Health Organization (WHO)

153

What is the purpose of hammering during normalising? 

  1. ((a))

    To harden the steel

  2. ((b))

    To increase brittleness

  3. ((c))

    To refine the grain structure and improve mechanical properties

  4. ((d))

    To remove oxidation

Show Answer
Answer: ((a))

To harden the steel

154

__________ type of lapping is used for precision finishing of engine cylinder bores. 

  1. ((a))

    Belt lapping

  2. ((b))

    Chemical lapping

  3. ((c))

    Internal lapping

  4. ((d))

    Flat lapping

Show Answer
Answer: ((a))

Belt lapping

155

If the current flowing through a conductor is 5 A and the resistance of the conductor is 10 ohms, what will be the voltage across the conductor, according to Ohm's Law?

  1. ((a))

    15 V

  2. ((b))

    10 V

  3. ((c))

    50 V

  4. ((d))

    5 V

Show Answer
Answer: ((a))

15 V

156

Gaskets, seals and spacers are made using: 

  1. ((a))

    hollow punch

  2. ((b))

    centre punch

  3. ((c))

    pin punch

  4. ((d))

    prick punch

Show Answer
Answer: ((a))

hollow punch

157

When the size of the shaft or male part of a job is more than hole or female part, the difference between the two will be known as ____________. 

  1. ((a))

    positive allowance

  2. ((b))

    negative allowance

  3. ((c))

    neither positive nor negative allowance

  4. ((d))

    either positive or negative allowance

Show Answer
Answer: ((a))

positive allowance

158

A drawing instrument box is used to carry all ______________ instruments.

  1. ((a))

    casting

  2. ((b))

    drilling

  3. ((c))

    drawing

  4. ((d))

    screening

Show Answer
Answer: ((a))

casting

159

What is the purpose of a split die in pipe threading?

  1. ((a))

    To change pipe diameter

  2. ((b))

    To remove metal burrs

  3. ((c))

    To create internal threads

  4. ((d))

    To adjust the depth of cut for external threads

Show Answer
Answer: ((a))

To change pipe diameter

160

Which of the following types of pliers is used to shape loops in wires and to form curves in light metal strips?

  1. ((a))

    Flat nose pliers

  2. ((b))

    End cutting pliers

  3. ((c))

    Round nose pliers

  4. ((d))

    Slip-joint pliers

Show Answer
Answer: ((a))

Flat nose pliers

161

Non-functional dimensions are _______________. 

  1. ((a))

    not essential for the function of the space or component

  2. ((b))

    essential for the function of the space or component

  3. ((c))

    derived from the values of the related features of a drawing

  4. ((d))

    directly derived from the values given on a drawing

Show Answer
Answer: ((a))

not essential for the function of the space or component

162

Which of the following is NOT a failure mode of ball bearings?

  1. ((a))

    Spalling

  2. ((b))

    Brinelling

  3. ((c))

    Creep

  4. ((d))

    Bending

Show Answer
Answer: ((a))

Spalling

163

After heating, how should the workpiece be cooled in the normalising process?

  1. ((a))

    By quenching in water

  2. ((b))

    By quenching in oil

  3. ((c))

    By cooling in still air

  4. ((d))

    By keeping inside the furnace

Show Answer
Answer: ((a))

By quenching in water

164

Toughness is the ability of a material to:

  1. ((a))

    undergo plastic deformation without failure

  2. ((b))

    absorb energy before fracture

  3. ((c))

    resist elastic deformation

  4. ((d))

    resist scratches and indentation

Show Answer
Answer: ((a))

undergo plastic deformation without failure

165

What does 'charging' of a lapping tool mean?

  1. ((a))

    Increasing the weight of the tool for better pressure

  2. ((b))

    Applying coolant to the tool

  3. ((c))

    Embedding abrasive particles into the lap surface

  4. ((d))

    Electrically energising the tool

Show Answer
Answer: ((a))

Increasing the weight of the tool for better pressure

166

The unit for specific gravity is _____. 

  1. ((a))

    no unit (dimensionless)

  2. ((b))

    kg/m3

  3. ((c))

    g/cm3

  4. ((d))

    m/s2

Show Answer
Answer: ((a))

no unit (dimensionless)

167

In electrical applications, why are MOSFETs used instead of BJTs?

  1. ((a))

    They have very high input impedance

  2. ((b))

    They have lower efficiency compared to BJTs

  3. ((c))

    They are suitable only for AC or DC signals

  4. ((d))

    They are expensive devices

Show Answer
Answer: ((a))

They have very high input impedance

168

Silicon carbide as a honing abrasive is best suited for which type of material?

  1. ((a))

    Soft materials like aluminium

  2. ((b))

    Hard materials like hardened steel and cast iron

  3. ((c))

    Rubber

  4. ((d))

    Plastic and wood

Show Answer
Answer: ((a))

Soft materials like aluminium

169

Which hardness test uses a diamond pyramid-shaped indenter? 

  1. ((a))

    Rockwell

  2. ((b))

    Brinell

  3. ((c))

    Shore

  4. ((d))

    Vickers

Show Answer
Answer: ((a))

Rockwell

170

In a forward Vernier scale, the size of one Vernier scale division is:

  1. ((a))

    larger than 1 main scale division

  2. ((b))

    1 mm

  3. ((c))

    equal to 1 main scale division

  4. ((d))

    smaller than 1 main scale division

Show Answer
Answer: ((a))

larger than 1 main scale division

171

In a velocity-time graph, the negative slope represents _____. 

  1. ((a))

    retardation

  2. ((b))

    distance

  3. ((c))

    displacement

  4. ((d))

    acceleration

Show Answer
Answer: ((a))

retardation

172

What should you do to ensure your personal safety at work?

  1. ((a))

    Take risks to finish tasks quickly.

  2. ((b))

    Ignore warning signs and instructions.

  3. ((c))

    Wear personal protective equipment.

  4. ((d))

    Work in a hurry without checking equipment.

Show Answer
Answer: ((a))

Take risks to finish tasks quickly.

173

When using a multimeter to measure current, which of the following is correct?

  1. ((a))

    The multimeter is connected only across resistive components.

  2. ((b))

    The multimeter is connected directly to the power source.

  3. ((c))

    The multimeter is connected in parallel with the load.

  4. ((d))

    The multimeter is connected in series with the load.

Show Answer
Answer: ((a))

The multimeter is connected only across resistive components.

174

Which of the following is an important safety measure during a power failure?

  1. ((a))

    Ignoring alarm systems

  2. ((b))

    Using candles for lighting

  3. ((c))

    Ensuring all machines and electrical equipment are turned off 

  4. ((d))

    Continuing to use equipment without verifying power status

Show Answer
Answer: ((a))

Ignoring alarm systems

175

Which of the following tools is NOT under the requirement to complete the Step Turning Process?

  1. ((a))

    Turning tool

  2. ((b))

    Vernier Caliper

  3. ((c))

    Snipping tool

  4. ((d))

    Parting Tool

Show Answer
Answer: ((a))

Turning tool

Attempt this paper under real exam conditions

Timed interface, section switching, instant scoring, and question-by-question analytics — free.

Start Timed Attempt