ISRO Draughtsman Civil Official Paper (Held On: 21 Apr, 2018) (Previous Year Paper)

The scale of the drawing is 1.0 mm = 1.0 m, then the Representative Fraction (RF) is______

When the full brick is laid with its length parallel to the face of wall is called ______

The scale of chords is used to measure ______

Initial setting time of cement is ______

A window projecting outward from the wall of a room is termed as ______

The width of the steps in staircase is called_______

In the normal building, the minimum height of the plinth is to be given above GL is ______

Construction in brick wall with alternate course of headers and stretchers are called ______

Terrazzo flooring is also called ______

A tool used to check the verticality of the structure is called ______

A wall built around top of flat roof which acts as a protection wall for the users is called ______

 A survey is being made to collect the required data for design and construction of all structures is known as:

Volume of a solid circular steel rod is 314.2 cubic centimeter and its diameter is 2 cm. Then its length is ______

A pipe which is provided for air circulation to the drainage system is called ______

A metallic chain using in chain surveying are provided with joining many number of links and the each length link is ______

A horizontal projection ornamentally moulded immediately below the roof (or) junction of wall and ceiling is called ______

The process of drying timber (or) removing moisture from a freshly felled tree is called ______

An estimate which is prepared by working out the quantity of each item of work based on the drawing and finding out the total cost is called ______

A slope provided in cross section of the road surface on both sides to drain out the rainwater is called ______

The conversion of dry land into green development by providing grass and natural scenery of vegetation is called _____

 The horizontal layer of mortar upon which bricks are laid in brick masonry is called ______

The bricks made with cavities are known as ______

Construction of brick wall with headers and stretchers in all layers is called _____

The difference in levels of the outer and inner edges of the road along the length of curve is called ______

The mass per unit volume is called ______

 Many types of pipes are used in water supply works in which maximum diameter of pipes are available in _______

The effective length of a compression member is less than three times the least lateral dimension is known as:

 The slope provided in the longitudinal direction of the road is called ______

 A temporary structure having platform which is used to further raising the building construction is known as:

A temporary designed structure carried out to hold the concrete in position till it sets are called _______

Health faucet is to be fixed in______

One member is placed over the other and the two are connected by means of rivets (or) weld, the joint is called:

The process by which making channel in wooden frame to receive the tongue of the other plank for making shutters is called ______

The bridges constructed by two or more hanging cables in a curve shape and supporting the road way is called:

A pictorial chart is made for construction project in item wise with the duration of time is known as _______

The process of concrete (or) masonry are kept wet for at least 7 days are called ______

The process by which the exposed surface of a wooden member is covered with a thin sheet of costly type of good wood to improve its appearance is called ______

 The projection of tread above the riser in staircase are called ______

Size of the brick is ______

What is meant by PPC ?

The size of the A0 size drawing sheet is ______

Find the weight of water if the water tank of size 1.00 m × 1.00 m × 1.00 m is fully filled. 

Roof which slopes in four direction is called ______

Allowable moisture content in timber is ______

Wedge shaped stone at apex of arch is ______

A line drawn with a long section, short dash and another long section is a ______

Command used to make corner in circular shape is ______

Short key for offset command is ______

Which command convert discrete objects in Polyline?

What is meant by UCS?

How many points do you need to define for rectangle command?

The ratio between the two adjacent sides of a drawing sheet is ______

In a drawing letters and numbers are designed by their ______

Eccentricity is always equal to 1 for ______

The main corrosive resisting pigment in paint is ______

Lower edge of inclined roof is ______

The inclination of stair to horizontal should be limited to ______ 

GI Pipe has a coating of ______

Upper horizontal member of a door frame is called ______

Dimensioning system used in Engineering drawing is ______