What is the diameter (in cm) of a sphere of surface area 1386 cm2?
- AOption (a)
14
- BOption (b)
21
- COption (c)
10.5
- DOption (d)
24.5
View answer & explanationHide answer & explanation
Correct answer
14
Held in 2019
Paper last updated:
Take this paper as a timed mock test. Review your answers after you submit.
Read the paper at your pace. Open an explanation when you need it.
What is the diameter (in cm) of a sphere of surface area 1386 cm2?
14
21
10.5
24.5
Correct answer
14


The bar graph shows the population density of 6 countries in 2000 and 2010.
If the population of country B is 10 million in 2000 and the population of country D is 6 million in 2010, how much more is the area of country B than the area of country D, where population density is measured as the number of people per 100 square kilometers.
500%
20%
400%
25%
Correct answer
500%


The bar graph shows all the ingredients (in grams) required to make two types of salads, X and Y. If Ingredient B of Salad X is reduced by 100 grams and Ingredient E of salad Y is increased by 25% then salad Y would be lighter than salad X by _______.
37.50%
25%
20%
22.50%
Correct answer
37.50%
In a steady-flowing river, a boat goes a certain distance upstream at a speed of 12 km/h and comes back the same distance at 24 km/h. Find the average speed for the total journey.
15 km/h
16 km/h
18 km/h
20 km/h
Correct answer
15 km/h
Find mass of an iron cube of side 2 cm. (Density of iron is 7.8 gm/cm3)
3.9 gm
0.975 gm
15.6 gm
62.4 gm
Correct answer
3.9 gm
Two cars, X and Y, travel from A to B at average speeds of 50 km/hr and 75 km/hr respectively. If X takes 2 hours more than Y for the journey, then the distance between A and B in km is ______.
600
400
800
300
Correct answer
600
If a shopkeeper sells an item at Rs. 2,700, he makes 8% profit. If he sells the item at Rs. 3,000 what will be the percentage of profit?
12
20
10
25
Correct answer
12
Find the highest common factor of 506 and 782.
29
34
46
22
Correct answer
29
A alone can do a task in 35 days and B alone in 14 days. If they work on it together for 5 days, then what fraction of the task is left?
Quarter
One-thirds
Half
Three fourths
Correct answer
Quarter
(0.12 - 0.0252) ÷ (0.1 - 0.025) = ______.
0.325
0.125
0.625
0.25
Correct answer
0.325
Find the coordinates of the midpoint of the segment joining the points (-4, 7) and (2, 3).
(-1, 5)
(-2, 3)
(1, -5)
(2, 4)
Correct answer
(-1, 5)
20 - 2[25% of (15 × 8 ÷ 6 + 12)] = ______
4
6
10
8
Correct answer
4
If a - b = 5 and ab = 14, then find a2 + b2.
53
27
5
19
Correct answer
53
Find the value of 5 sin θ - 2 cosec θ, if θ = 30°.
3/2
2/3
Correct answer
3/2
In a certain gear train, the driver has 18 teeth while the follower has 8 teeth. For every 16 turns of the driver, the follower turns ______ times.
18
8
36
9
Correct answer
18
If 5x/2 - 1/4(6x - 5/3) = 7/6, then the value of x is ______.
5/4
3/4
3/7
5/7
Correct answer
5/4
If the amount received at the end of 1st and 2nd year at compound interest on a certain principal is Rs. 1,350 and Rs. 1,458 respectively, what is the rate of interest?
10%
15%
12%
8%
Correct answer
10%
A trader buys 60 bags of grain at Rs. 400 each. If he sells 18 bags at 8% profit, at what price should he sell the remaining bags to make 16.4% overall profit on selling the 60 bags?
Rs. 480
Rs. 500
Rs. 540
Rs. 520
Correct answer
Rs. 480
If A, B and C can do a task working alone in 12, 18 and 36 days respectively. They all work together for 2 days, then B quits. How many days A and C working together will take to complete the remainder of the task?
6
3
4
9
Correct answer
6
What is the area (in cm2) of an equilateral triangle of side 8 cm?
32√3
8√3
64√3
16√3
Correct answer
32√3
A and B start to walk from point P towards point Q. The distance between P and Q is 9 km. B starts 4 minutes after A. A, on reaching Q, immediately returns and after walking a kilometre meets B. If A’s speed is a kilometre in 10 minutes, what is B’s speed in kilometres per minute?
1/15
1/8
1/12
1/6
Correct answer
1/15
Pipe A can fill a tank in 6 hours. Pipe B can empty it in 15 hours. If both the pipes are opened together, then the tank will be filled in how many hours?
9
8
12
10
Correct answer
9
When a number is increased by 36, it becomes 109% of itself. What is the number?
300
450
360
400
Correct answer
300
A bullet travels 90 m in 0.2 seconds. Find its speed in km/hr.
162
1,620
1,250
125
Correct answer
162
An executive earns a salary of Rs. 12,600 every month, and he spends 5/7 of it. If his salary increases by 1/3rd and his spending increases by 1/5th of the present expenditure, what fraction of his salary will he save?
7/16
8/15
7/15
5/14
Correct answer
7/16
If 3A = 6B = 7C; find A : B : C.
12 : 7 : 3
7 : 12 : 6
14 : 7 : 6
7 : 3 : 12
Correct answer
12 : 7 : 3
Find x if the mean of the numbers 10, 4, 1, 15, 15, x, 12 and 14 is 10.
7
8
9
10
Correct answer
7
If √X + 0.24 = √0.1296 then find X.
0.0144
0.12
1.44
0.0012
Correct answer
0.0144
The weights of 3 boxes are 4, 7 and 10 kilograms. Which of the following CANNOT be the total weight, in kilograms, of any combination of these boxes?
14
21
17
18
Correct answer
14
The author of ‘The Monk Who Sold His Ferrari’ is ______.
Arvind Adiga
Robin Sharma
Manohar Malgonkar
Arundhati Roy
Correct answer
Arvind Adiga
Find the work done (in kJ) if a force of 750 N pushes a cart of mass 30 kg by 16 m.
24
12
36
48
Correct answer
24
Which hazardous substance can cause lung cancer?
Benzene vapours
Asbestos particles
Herbicides
Aluminum
Correct answer
Benzene vapours
______ is the physiological adjustment by an organism to environmental change.
Bioremediation
Bioaccumulation
Cogeneration
Acclimation
Correct answer
Bioremediation
Which of the following gases is a highly poisonous, odourless, tasteless and colourless gas?
Carbon dioxide
Carbon monoxide
Methane
Nitrogen dioxide
Correct answer
Carbon dioxide
Green and yellow vegetables in our diet mostly provide us which element as food?
Copper
Sodium
Zinc
Potassium
Correct answer
Copper
Binary 110110101 is equal to decimal ________.
333
437
349
477
Correct answer
333
A/An ______ is software used to maintain the security of a private network.
malware
encryption
firewall
clickbait
Correct answer
malware
Who was the chairman of the Constitution Drafting Committee?
Jawaharlal Nehru
Dr. B R Ambedkar
Dr. Rajendra Prasad
Sardar Patel
Correct answer
Jawaharlal Nehru
The Umaid Bhawan Palace is in which city?
Jaipur
Jodhpur
Bikaner
Udaipur
Correct answer
Jaipur
Classical musician Shivkumar Sharma is associated with which musical instrument?
Shehnai
Tabla
Violin
Santoor
Correct answer
Shehnai
Which of the following folk dances is from Assam?
Giddha
Lezim
Nati
Bagurumba
Correct answer
Giddha
-100° Celsius = ______ Fahrenheit
-373°
-148°
173°
-212°
Correct answer
-373°
If 36 J of work is done in moving a charge Q across 8 V, find Q (in coulombs).
288
9
4.5
16
Correct answer
288
What is the relative density of a solid of mass 50 gm which when fully immersed in water weighs 10 gm?
5
1.25
2.5
0.8
Correct answer
5
If the speed of a car increases from 54 km/hr to 90 km/hr, its kinetic energy increases in the ratio of ________.
3/5
9/4
9/16
9/25
Correct answer
3/5
Find the length (in cm) of the edge of a cube of a piece of wood which weighs 80 N. (Use g = 10 m/s2, density of wood = 1 g/cm3)
60
20
80
40
Correct answer
60
Two resistors of R Ω and 60 Ω are connected in parallel to get an effective resistance of 24 Ω. Find R.
56
64
48
40
Correct answer
56
Farad per meter is the unit of ______.
watt per steradian
permittivity
permeability
electric conductance
Correct answer
watt per steradian
A ______ map converts color intensity or grayscale information to heights to give the appearance that features are raised above the surface, like embossed letters.
shade
bump
tone
tint
Correct answer
shade
A truck of mass 5000 kg accelerates from 25 m/s to 35 m/s. Find the change in its kinetic energy (in MJ).
1
2.5
1.5
2
Correct answer
1
Which of the following recipients of the Dadasaheb Phalke Award received it posthumously?
Vinod Khanna
Satyajit Ray
Naushad
Durga Khote
Correct answer
Vinod Khanna
To ______ is to prepare a storage medium, usually a disk, for reading and writing.
format
defrag
map
boot
Correct answer
format
Which of the following is the correct relation between resistance ‘R’, conductivity ‘σ’, length ‘L’ and area of cross section ‘A’ of a metal wire?
RL = Aσ
RσA = L
RA = Lσ
σ = RL/A
Correct answer
RL = Aσ
Which team won the Indian Premier League (IPL) in 2018?
Sunrisers Hyderabad
Chennai Super Kings
Royal Challengers Bangalore
Kolkata Knight Riders
Correct answer
Sunrisers Hyderabad
Antihistamines are found in some first-aid boxes. When should these drugs be taken?
To aid in clotting of blood
To ease the symptoms of hay fever and other allergies
To ease the indigestion and heartburn
To bring relief from asthma
Correct answer
To aid in clotting of blood
Acceleration due to gravity on moon is 1/6th that on earth. How much would an astronaut weigh on the moon if he weighs 90 kgf on earth? (acceleration due to gravity on earth = 10 m/s2)
15 N
150 N
90 N
9 N
Correct answer
15 N
Which of the following is NOT a base unit?
mole
ampere
radian
candela
Correct answer
mole
Who invented the blue jeans?
Levi Strauss
Todd Oldham
Calvin Klein
Gianni Versace
Correct answer
Levi Strauss
Find the potential difference (in V) across a resistance of 2.5 kΩ through which a 2 mA current flows.
5
0.2
1.25
0.8
Correct answer
5
The Living Planet Report, released every two years, is the flagship publication of which organisation?
The Nature Conservancy
World Wide Fund for Nature
Conservation International
Wildlife Conservation Society
Correct answer
The Nature Conservancy
The sum of two binary numbers 1101111 and 1100101 is ______.
100011100
100000110
11110000
11010100
Correct answer
100011100
The National Skills Development Corporation (NSDC) is a public-private partnership formed under India’s ______.
Ministry of Finance
Ministry of Electronics & Information Technology
Ministry of Corporate Affairs
Ministry of Science & Technology
Correct answer
Ministry of Finance
The resistance of a metal rod depends on all of the following, except ______.
resistivity
density
length
temperature
Correct answer
resistivity
Find the missing number in the given series.
-1.3, -0.8, -0.3, ?, 0.7, 1.2
0.1
0.3
0.4
0.2
Correct answer
0.1
One statement is given, followed by two assumptions, I & II. You have to consider the statement to be true, even if it seems to be at variance from commonly known facts. You are to decide which of the given assumptions can definitely be drawn from the given statement.
Statement: “You are appointed as a trainee accountant on temporary basis. Your employment status will automatically be converted to permanent on submission of pass result of M Com final exam." — Extract from an appointment letter.
Assumptions:
I. M Com final exam is a reasonable proof of an accountant's capability.
II. All trainees are appointed on temporary basis.
Both I and II are implicit
Only assumption I is implicit
Only assumption II is implicit
Neither I nor II is implicit
Correct answer
Both I and II are implicit
Choose the figure which is different from the rest.




Correct answer
In a certain code language, ‘+’ represents ‘×’, ‘÷’ represents ‘+’, ‘-’ represents ‘÷’ and ‘×’ represents ‘-’. Find out the answer to the following question.
12 ÷ 6 – 2 + 10 × 5 = ?
50
37
23
16
Correct answer
50
In the following figure, the triangle represents actors, the square represents professors, the circle represents Indians and the rectangle represents fathers. Which set of letters represents Indians who are either professors or fathers?

IGH
CEF
E
G
Correct answer
IGH
Choose the letters which are different from the rest.
HJL
PRT
VTR
UWY
Correct answer
HJL
Select the option that is related to the third word on the same basis as the second word is related to the first word.
Letter : Envelope ∷ Dagger : ?
Sheath
Weapon
Sword
Sharp
Correct answer
Sheath
If A $ B means A is the husband of B, A # B means A is the brother of B and A * B means A is the mother of B, then what does P $ Q * R # S mean?
P is the father of S
P is the brother-in-law of S
P is the son of S
P is the brother of S
Correct answer
P is the father of S
What is the angle between the hour hand and the minute hand at half past two?
105°
75°
120°
90°
Correct answer
105°
The given Venn diagram shows the number of students who have passed in the three exams, viz. English, Science and Maths. How many students failed in all the three exams?

3
12
9
6
Correct answer
3
One statement is given followed by two conclusions. Decide which of the given conclusions can definitely be drawn from the given statement.
Statement: As income increases, cars become more affordable.
Conclusion I: With greater use of technology, cars are now cheaper than they were a generation ago.
Conclusion II: Cars will become so numerous that no future technology will solve the traffic problem.
Only conclusion I follows
Both I and II follow
Neither I nor II follows
Only conclusion II follows
Correct answer
Only conclusion I follows
A postman starts from the post office and cycles 13 km south, then turns west and cycles 10 km, then turns north and cycles 8 km, then turns east and cycles 2 km and then turns to his left and cycles 5 km. Where is he now with reference to his starting position?
8 km east
12 km east
12 km west
8 km west
Correct answer
8 km east
Here are some words from an artificial language.
unacri means lighthouse
bancri means lightweight
banetu means overweight
Which word would mean ‘overdrive’?
adiban
adietu
simuna
criteh
Correct answer
adiban
At present, the ratio between the ages of Anu and Dimpy is 5 : 8. After 2 years, the ratio of their ages will become 2 : 3. What was Dimpy’s age before 2 years?
10
12
16
14
Correct answer
10
In the question, two statements are given, followed by three conclusions, I, II and III. You have to consider the statements to be true even if they seem to be at variance with commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statements.
Statement:
All flags are banners.
Some flags are emblems.
Conclusion:
I. Some emblems are banners.
II. All banners are emblems.
III.No emblems are banners.
Only conclusion I follows
Only conclusion III follows
All conclusions I, II and III follow
Only conclusion I and III follow
Correct answer
Only conclusion I follows
Choose the one which is different from the rest.
Father
Son
Mother-in-law
Brother
Correct answer
Father
Select the option that is related to the third word on the same basis as the second word is related to the first word.
Poem : Stanza ∷ Book : ?
Language
Story
Page
Printing
Correct answer
Language
If 8 # 12 = 10; 5 # 9 = 7; 6 # 10 = 8, then find the value of 14 # 4.
10
9
5
3
Correct answer
10
In a certain code DIRTY is coded as 24759 and FOAM is coded as 1863. Using the same code ARID will be coded as ______.
2489
9165
1579
6742
Correct answer
2489
In the following question, which set of letters and numbers, when sequentially placed at the gaps in the given series, shall complete it?
1_2x_bb_yy_cc_6zzz
a345c
3a45b
3a4b5
3a45c
Correct answer
a345c
A said to B, “You are my husband’s daughter-in-law’s son.” How is B related to A?
B is the father of A
B is the grandson of A
B is the brother of A
B is the son of A
Correct answer
B is the father of A
In the question, two statements are given, followed by two conclusions, I, and II. You have to consider the statements to be true even if they seem to be at variance from commonly known facts. You have to decide which of the given conclusions, if any, follows from the given statements.
Statement 1: Some wagons are buggies.
Statement 2: All wagons are carts.
Conclusion I: All buggies are carts.
Conclusion II: Some carts are buggies.
Only conclusion I follows
Both I and II follow
Neither I nor II follows
Only conclusion II follows
Correct answer
Only conclusion I follows
Rearrange the parts of the sentence in the correct order.
A customer based on reasons
X- chances are that they actually made the change
Y- may not come out of the changing room, but
Z- which is unfortunately inappropriate
YXZ
ZYX
XZY
ZXY
Correct answer
YXZ
Find the power (in W) of a pump if it can lift 1 tonne of water by 90 m in 30 minutes. (Assume 100% efficiency and use g= 10 m/s2)
50
250
25
500
Correct answer
50
Which of the following is an example of a first class lever?
Ice tongs
Wheel barrow
A pair of scissors
Nut cracker
Correct answer
Ice tongs
_______ curves employ at least three points to define a curve. The two endpoints of the curve are called anchor points. The other points, which define the shape of the curve, are called handles, tangent points, or nodes.
Bicorn
Bezier
Deltoid
Kappa
Correct answer
Bicorn
Find the efficiency of a pulley system which has a mechanical advantage of 2.5 and where the load lifts by 2.5 meters on pulling the rope by 10 m.
62.50%
25.00%
40.00%
100.00%
Correct answer
62.50%
________ is when we cover a surface with a pattern of flat shapes so that there are no overlaps or gaps.
Tessellation
Tracking
Gradient
Kerning
Correct answer
Tessellation
If half a litre of hot water at 90°C is mixed with three and a half litres of cold water at 10° C, find the final equilibrium temperature (in °C) if no heat is lost.
20
40
30
50
Correct answer
20
Two children, weighing 30 kg and 15 kg, sit on one side of a see-saw at a distance of 1 m and 1.2 m respectively, from the fulcrum. A boy of 'M' kg sits on the other side of the see-saw at a distance of 1.2 m from the fulcrum, and the see- saw is in equilibrium. Find M.
36
45
48
40
Correct answer
36
Find the heat capacity of a pan of mass 200 g, if its temperature rises by 8° C on receiving 2000 J of heat.
250 JK-1
5 JK-1
50 Jkg-1K-1
1.25 Jkg-1K-1
Correct answer
250 JK-1
210 mm × 297 mm are the dimensions of ______ size paper.
A4
A2
A3
A1
Correct answer
A4
The sentences given in the question, which, when properly sequenced, form a coherent paragraph. Each sentence is labelled with a letter. Choose the most logical order of sentences from among the given choices to construct a coherent paragraph.
Outside their window there was a vine with attractive foliage, but it started shedding leaves one by one as summer passed through fall into winter.
A - Came dawn, when Johnsy looked out of the window from her sick bed, lo and behold, the leaf was still there and it continued to be there on the following days.
B - Finally, only one last leaf remained. Johnsy told Sue that when that leaf fell, her life would also go.
C - The girl regained her will to live and was fully recovered in a few days.
D - A concerned elderly artist friend of the girls, hearing this story, climbed outside the window in the bitterly cold night and painted a life-like leaf at the spot from where the last leaf had just fallen.
BDCA
BDAC
DBCA
DBAC
Correct answer
BDCA
An object with greater ______ has greater inertia.
velocity
acceleration
volume
mass
Correct answer
velocity
Find the specific heat capacity (in Jg-1K-1) of a block of metal of mass 500 g, the temperature of which rises by 80°C when it absorbs 10 kJ of heat?
0.4
0.16
1.56
0.25
Correct answer
0.4
Find the specific latent heat of vaporisation of 1.25 g of nitrogen (in Jg-1), if it releases 250 Joules of heat when it condenses at its boiling point of 196° C.
469
500
312.5
200
Correct answer
469
What is the function of a sensor in the MPFI system?
It senses the information in the form of physical and chemical variables.
It does the mechanical work.
It controls the pressure.
It operates the injector.
Correct answer
It senses the information in the form of physical and chemical variables.
Which of the following conductors is used in bulbs?
Carbon
Copper
Tungsten
Nichrome
Correct answer
Carbon
In an overhead valve system, the cylinder head supports the_________.
crankshaft
oil pan
oil pump
rocker shaft assembly
Correct answer
crankshaft
The two commonly used semiconductor materials are:
arsenic and boron
aluminium and antimony
gallium and indium
germanium and silicon
Correct answer
arsenic and boron
Distributor-type FIP is also called:
low-pressure pump
rotary pump
servo pump
in-line pump
Correct answer
low-pressure pump
The function of an alternator in vehicles is to:
discharge the battery
measure the voltage
measure the current
charge the battery
Correct answer
discharge the battery
Supercharging in marine engines is done to:
decrease the engine power output
decrease the fuel pressure
increase the fuel pressure
increase the engine power output
Correct answer
decrease the engine power output
Which of the following is a common reason for using aluminium sheets?
Lightness
Dullness
Brightness
Darkness
Correct answer
Lightness
Halon extinguishers are filled with:
kerosene
liquefied petroleum gas
carbon tetrachloride
water
Correct answer
kerosene
Which types of rims are used generally in light vehicles?
Split-type
Wire spoke
Press - type
Artillery
Correct answer
Split-type
What does NDT stand for?
Non - Destructive Test
Non - Dial Test
Non - Driving Test
Non - Dry Test
Correct answer
Non - Destructive Test
The most common base material for ICs is:
germanium
silicon
gallium
carbon
Correct answer
germanium
A _______ is mounted on the rear end of a crankshaft.
flywheel
timing sprocket
vibration damper
counter weight
Correct answer
flywheel
Connecting rods are made of:
Aluminium
mild steel
alloy steel
cast iron
Correct answer
Aluminium
The cylinder head is a single casting bolted on the top of the _______.
Camshaft
crankshaft
oil sump
cylinder block
Correct answer
Camshaft
The taper shank drills should be mounted on the machine spindles by means of a _______.
Sleeve
tang of file
Hammer
Punch
Correct answer
Sleeve
The choke in the carburettor is generally used when the engine is:
running at high speed
to be suddenly accelerated
to be cold started
Idling
Correct answer
running at high speed
In a Distributor less ignition system the distributor is replaced by:
Brushes
Insulated coils
Ignition switch
Rotor
Correct answer
Brushes
The part that must be fitted in a piston to ensure a good seal with the cylinder wall is called:
piston rings
piston pins
connecting rods
Gaskets
Correct answer
piston rings
In the differential, the crown wheel is attached to the ________.
bevel pinion
propeller shaft
bevel gear
differential cage
Correct answer
bevel pinion
Stoichiometric ratio is associated with:
compression pressure
mechanical efficiency
air to fuel ratio
volumetric efficiency
Correct answer
compression pressure
Which of the following type of steering gear box is most widely used in passenger cars?
Recirculating ball type
Worm and nut
Rack and pinion
Worm and wheel
Correct answer
Recirculating ball type
What is determined while measuring a component?
Nominal size
Actual size
Scale size
Specified size
Correct answer
Nominal size
Piston pin connects piston and _________.
connecting rod
valve
crankshaft
camshaft
Correct answer
connecting rod
What is the function of hydraulic pumps in hydraulic systems?
To permit the pressure in the reservoir to force fluid into the pump
To develop pressure on the surface of oil
To deliver fluid into the hydraulic system
To produce flow only and not pressure
Correct answer
To permit the pressure in the reservoir to force fluid into the pump
Which of the following is a temporary joint?
Welded joint
Soldered joint
Press fit joint
Riveted joint
Correct answer
Welded joint
A radiator core should be cleaned _________.
from top to bottom of the core
from top hose to bottom hose
from the outside to the side of the fan
by reverse flushing
Correct answer
from top to bottom of the core
Which of the following is the function of a flywheel?
It drives the camshaft.
It controls the crankshaft end play.
It supports the timing gear.
It serves as a mounting and frictional surface for clutch assembly.
Correct answer
It drives the camshaft.
A die is:
an external thread cutting tool
an acme thread cutting tool
an internal thread cutting tool
a square thread cutting tool
Correct answer
an external thread cutting tool
The purpose of holding the hammer handle at its end is to:
avoid injury to hand
have maximum leverage
avoid damage to workpiece
get a proper grip
Correct answer
avoid injury to hand
The colour of the negative plates of a lead acid battery is:
Black
White
Brown
Grey
Correct answer
Black
The track rod is connected to the track arm by a_________.
ball joint
stub axle
king pin
universal joint
Correct answer
ball joint
Theoretically, ignition in an engine should occur at:
BDC at the start of the power stroke
TDC at the end of the compression stroke
TDC at the start of the compression stroke
BDC at the end of the induction
Correct answer
BDC at the start of the power stroke
The sensor which measures the outside air entering the engine:
Mass air flow sensor (MAF)
Throttle position sensor (TPS)
Manifold Absolute pressure sensor (MAP)
Oxygen sensor
Correct answer
Mass air flow sensor (MAF)
Which fire extinguisher is suitable for live electrical fire?
CO2
Liquefied chemical
Water filled
Halon
Correct answer
CO2
Rotary motion of the steering wheel is converted into a reciprocating motion by the ______.
track rod
steering gear box
stub axle
track arm
Correct answer
track rod
Which component acts as the drive device in the automobile air conditioning system?
Condenser
Receiver
Compressor
Evaporator
Correct answer
Condenser
A 12-V lead acid battery consists of:
six cells in parallel
three cells in series
three cells in parallel
six cells in series
Correct answer
six cells in parallel
Which of the following is NOT a part of the MPFI system?
Throttle position sensor
Electronic fuel injector
Carburettor
Electrical fuel pump
Correct answer
Throttle position sensor
The fuel injection timing in a distributor type injection system is controlled by: (Choose the correct option)
changing the number of cams on the ring
rotating the cam ring
changing the plunger stroke
changing the speed of the rotor
Correct answer
changing the number of cams on the ring
Spark plug of automobile consist of two electrodes one is ground electrode and the other is:
Dielectric electrode
Zero electrode
Central electrode
Right electrode
Correct answer
Dielectric electrode
Taps are re-sharpened by grinding:
diameter
threads
flutes
relief
Correct answer
diameter
CRDI stands for:
Common Regular Direct Interval
Common Rack Direct Injection
Common Rail Distributor Injector
Common Rail Direct Injection
Correct answer
Common Regular Direct Interval
Identify the locking arrangement in the following figure.

Wire fasteners
Corrugated head screw
Tab washers
Castle nut with split pin
Correct answer
Wire fasteners
The viscosity of a fluid offers resistance to:
flow
sound
light
current
Correct answer
flow
What is the purpose of a fog light?
To produce yellow light rays during mist/fog
To read the working of gauges
To produce interior illumination
To indicate the vehicle is being parked.
Correct answer
To produce yellow light rays during mist/fog
The centre part of a typical universal joint is called the__________.
Joint
Bearing
Spider
Trunnion
Correct answer
Joint
The chisel will dig into the material when:
the rake angle is more
the angle of inclination is more
the angle of inclination is too low
the clearance angle is too low
Correct answer
the rake angle is more
Which type of lifting equipment is used in service stations for servicing of vehicles?
Hydraulic jack
Hydraulic press
Hydraulic hoist
Arbor press
Correct answer
Hydraulic jack
Which type of fuel injection pump has a plunger and barrel assembly for each cylinder of the engine?
Distributor pump
Inline pump
CRDI pump
Feed pump
Correct answer
Distributor pump
Gear box and differential together are enclosed in a box, which is called the _______.
Multi-axle
Transaxle
Gear box
Transfer case
Correct answer
Multi-axle
Which of the following is required between the ring gear and the pinion gear to allow for heat expansion and lubrication?
Shims
Hole
Pits
Backlash
Correct answer
Shims
Maximum oil pressure in the lubrication system is controlled by the _________.
pressure relief valve
pressure switch
oil filter
pump rotor
Correct answer
pressure relief valve
What controls the fuel metering and delivering in the MPFI system?
Relay
Fuse
Fusible link
Electronic control module
Correct answer
Relay
Pneumatic study deals with the study of systems operated with:
water
solid
air
oil
Correct answer
water
In distributor-less ignition systems, ignition can be adjusted manually by:
It cannot be adjusted manually.
adjusting screws
centrifugal weights
vacuum
Correct answer
It cannot be adjusted manually.
In a multi-cylinder engine, which of the following arrangements is considered to be the simplest?
V-engines
Cylinders in-line
Horizontally opposed type
Radial
Correct answer
V-engines
Which of the following does not require a coolant during reaming?
Aluminium
Copper
Cast iron
Steel
Correct answer
Aluminium
An alternator is generally fitted at ________ of the engine.
rear side
front side
centre
bottom side
Correct answer
rear side
Which of the following (gears) converts rotary motion into linear motion?
Rack and pinion
Herringbone gear
Worm gear
Helical gear
Correct answer
Rack and pinion
Which of the following is used to check the gap between contact breaker points?
Micrometer gauge
Wire gauge
Vernier gauge
Feeler gauge
Correct answer
Micrometer gauge
A turbocharger is mounted on the _________.
inlet manifold
front of the engine block
flywheel side
exhaust manifold
Correct answer
inlet manifold
The exhaust manifold in small diesel engines is made of:
Aluminium
Copper
Cast iron
Brass
Correct answer
Aluminium
Which of the following is NOT a heat treatment process?
Normalising
Tempering
Machining
Annealing
Correct answer
Normalising
Ammeter is connected to circuits in:
series or parallel
Open
Parallel
Series
Correct answer
series or parallel
A bent snip is used for:
bending a sheet
making holes on a sheet
removing the burr
cutting a sheet along a curved line
Correct answer
bending a sheet
Which of the following is used to measure the ovality of a cylinder bore?
Pressure gauge
Height gauge
Dial bore gauge
Vacuum gauge
Correct answer
Pressure gauge
The taper shank drills are held on machines by means of:
Chucks
Vices
Drifts
Sleeves
Correct answer
Chucks
In rear axle, what is used between the axle retainer plate and the housing to limit axle end play?
Spring washers
Shims
Thrust washers
Spring
Correct answer
Spring washers
Headlights are also used as:
side indicators
signalling devices
stop indicators
heating devices
Correct answer
side indicators
In an automatic transmission system, on gear shifting, lever R indicates:
Reverse
Parking
Forward
Drive
Correct answer
Reverse
Which part of the piston is subjected to high pressure and temperature?
Skirt
Crown
Ring section
Lead
Correct answer
Skirt
In diesel engines, fuel and air are mixed in the __________.
inlet port
combustion chamber
carburettor
injector
Correct answer
inlet port
The opening and closing of the valve in relation to the piston movement is called:
valve mechanism
valve timing
valve operation
valve overlap
Correct answer
valve mechanism
Which tool is used to remove and refit valves in a cylinder head?
Valve bend remover
Valve spring aligner
Valve spring remover
Spring tension tester
Correct answer
Valve bend remover
175 questions in the full paper