Official Paper

RRB ALP CBT-II (Mechanic Motor Vehicle) Official Paper (Held On: 06 May, 2025 Shift 1) (Previous Year Paper)

175 questions · 150 minutes · with answers · free

Attempt as Timed Mock Test

Part A (100 questions)

1

In this question, a statement is given followed by two courses of action, numbered I and II. You must assume everything in the statement to be true, and on the basis of the information given in the statement, decide which of the given courses of action logically follow(s) for pursuing.

Statement:

A major fire broke out this afternoon in a mall in Jaipur, causing several casualties amongst the people present inside.

Courses of Action:

The police must check to see if the fire safety regulations were followed by the mall.

Traffic police must divert traffic away from the fire site, to enable evacuation of people.

  1. ((a))

    Only II follows.

  2. ((b))

    Neither I nor II follows.

  3. ((c))

    Both I and II follow.

  4. ((d))

    Only I follows.

Show Answer
Answer: ((a))

Only II follows.

2

The taxi charges in a city consist of a fixed charge together with the charge per kilometre for the distance covered. For a distance of 35 km, the charge paid is ₹375 and for a distance of 48 km, the charge paid is ₹427. Find the fixed charges and the charge per km (in ₹), respectively.

  1. ((a))

    220 and 6

  2. ((b))

    227 and 5

  3. ((c))

    235 and 4

  4. ((d))

    275 and 3

Show Answer
Answer: ((a))

220 and 6

3

Which technology operates through an electrochemical process that transforms the energy stored in hydrogen gas (H2) and oxygen into electrical power without combustion?

  1. ((a))

    Hydroelectric power

  2. ((b))

    Solar thermal power

  3. ((c))

    Hydrogen fuel cells

  4. ((d))

    Wind power

Show Answer
Answer: ((a))

Hydroelectric power

4

Seema is twice as old as Alka. If nine years is subtracted from Alka’s age and six years is added to Seema’s age, then Seema will be four times Alka’s age. How old was Alka three years ago? 

  1. ((a))

    18 years

  2. ((b))

    21 years

  3. ((c))

    16 years

  4. ((d))

    20 years

Show Answer
Answer: ((a))

18 years

5

Read the given statements and conclusions carefully. Assuming that the information given in the statements is true, even if it appears to be at variance with commonly known facts, decide which of the given conclusion(s) logically follow(s) from the statements.

Statements:

Some ships are boats.

All boats are submarines.

Some submarines are yachts

Conclusions:

(I) Some yachts are boats.

(II) Some yachts are ships.

  1. ((a))

    Only conclusion (I) follows. 

  2. ((b))

    Both conclusions (I) and (II) follow.

  3. ((c))

    Only conclusion (II) follows.

  4. ((d))

    Neither conclusion (I) nor (II) follows.

Show Answer
Answer: ((a))

Only conclusion (I) follows. 

6

Eight people are sitting in two parallel rows containing 4 people each in such a way that there is equal distance between adjacent persons. In row 1 – A, B, C and D are seated and all of them are facing south. In row 2 – P, Q, R and S are seated and all of them are facing north. Thus each person faces another person from the other row. Only three people sit to the right of R. D faces the person who is the immediate neighbour of S and P. C faces the person who sits second to the left of S. R does not face A.

Who amongst the following faces B?

  1. ((a))

    R

  2. ((b))

    S

  3. ((c))

    P

  4. ((d))

    Q

Show Answer
Answer: ((a))

R

7

In Engineering Drawing, which of the following is the correct definition of the term 'dimension'. 

  1. ((a))

    The thickness of the line of a letter

  2. ((b))

    A continuous thick or wide line along which the prints are trimmed

  3. ((c))

    A line that is drawn to make a section evident

  4. ((d))

    A numerical value expressed in an appropriate unit of measurement 

Show Answer
Answer: ((a))

The thickness of the line of a letter

8

In a certain code language, ‘LOVE’ is coded as ‘8364’ and ‘EARS’ is coded as ‘3517’. What is the code for ‘E’ in the given code language?

  1. ((a))

    7

  2. ((b))

    5

  3. ((c))

    3

  4. ((d))

    4

Show Answer
Answer: ((a))

7

9

Study the given pie chart and answer the question that follows.

The given pie chart indicates the percentage-wise breakup of students in different subjects. The total number of students in the college is 5000.

What is the ratio of the students studying Zoology to the students studying Botany?

  1. ((a))

    15 : 14 

  2. ((b))

    15 : 16

  3. ((c))

    14 : 15

  4. ((d))

    16 : 15

Show Answer
Answer: ((a))

15 : 14 

10

Which of the following steps is essential when configuring a web browser to enhance both security and privacy for a user?

  1. ((a))

    Enabling pop-ups for all websites to improve user experience

  2. ((b))

    Setting the homepage to a frequently visited website for quick access

  3. ((c))

    Configuring the browser to block third-party cookies and enabling HTTPS-only mode

  4. ((d))

    Disabling the browser's cache to improve website loading times 

Show Answer
Answer: ((a))

Enabling pop-ups for all websites to improve user experience

11

Which of the following benefits can be obtained by conducting an energy audit in a commercial building?

  1. ((a))

    Increasing the cost of energy bills

  2. ((b))

    Identification of opportunities for energy savings

  3. ((c))

    Reduction in price of energy per its unit usage

  4. ((d))

    Reduced market value of building

Show Answer
Answer: ((a))

Increasing the cost of energy bills

12

What should come in place of the question mark (?) in the given series?

17 29 41 59 77 101 125 ?

  1. ((a))

    175

  2. ((b))

    161

  3. ((c))

    155

  4. ((d))

    149 

Show Answer
Answer: ((a))

175

13

Which of the following options is correct when two objects at the same temperature are kept in contact with each other? 

  1. ((a))

    Both objects transfer heat to each other.

  2. ((b))

    Heat is transferred from object 2 to object 1.

  3. ((c))

    No heat is transferred.

  4. ((d))

    Heat is transferred from object 1 to object 2. 

Show Answer
Answer: ((a))

Both objects transfer heat to each other.

14

What will come in place of the question mark (?) in the following equation, if ‘+’ and ‘−’ are interchanged and ‘×’ and ‘÷’ are interchanged?

32 + 28 ÷ 3 × 4 − 15 = ?

  1. ((a))

    32

  2. ((b))

    26

  3. ((c))

    29

  4. ((d))

    20

Show Answer
Answer: ((a))

32

15

Mangal starts from Point A and walks 14 m towards north. He takes a right turn, walks 9 m and then takes a right turn, walks 37 m, reaches Point B and stops. Jayanti starts from Point Z which is 15 m towards the east of Point B. She walks 11 m towards east, takes a left turn, walks 42 m, turns left and walks 63 m, turns left and walks 19 m and stops at Point Y. What is the shortest distance between Point A and Point Y? (All turns are 90 degree turns only.) 

  1. ((a))

    25 m

  2. ((b))

    28 m

  3. ((c))

    26 m

  4. ((d))

    31 m

Show Answer
Answer: ((a))

25 m

16

What is the amount of work done in moving a charge of 6 C from a point with a potential of 120 V to a point with a potential of 140 V? 

  1. ((a))

    840 J

  2. ((b))

    120 J

  3. ((c))

    720 J

  4. ((d))

    3.33 J

Show Answer
Answer: ((a))

840 J

17

In a clearance sale of electronic items, an item whose marked price was ₹12,225 is now sold for ₹10,758, d% is the discount percentage on the item. The value of d is: 

  1. ((a))

    11%

  2. ((b))

    14%

  3. ((c))

    12%

  4. ((d))

    13%

Show Answer
Answer: ((a))

11%

18

Which of the following is NOT a fundamental quantity in the SI system? 

  1. ((a))

    Luminous intensity

  2. ((b))

    Amount of substance

  3. ((c))

    Time

  4. ((d))

    Force

Show Answer
Answer: ((a))

Luminous intensity

19

Alloys are preferred over pure metals in electrical heating devices: 

  1. ((a))

    because the resistivity of an alloy is generally higher than its constituent metals.

  2. ((b))

    because alloys oxidise (burn) readily at high temperatures.

  3. ((c))

    because the elasticity of an alloy is higher than that of its constituent metals.

  4. ((d))

    because the resistivity of an alloy is lower than that of its constituent metals.

Show Answer
Answer: ((a))

because the resistivity of an alloy is generally higher than its constituent metals.

20

Which of the following correctly describes the direction of electric current? 

  1. ((a))

    From low potential to high potential

  2. ((b))

    Opposite to the direction of positive charge flow

  3. ((c))

    Same as the direction of electron flow

  4. ((d))

    Opposite to the direction of electron flow

Show Answer
Answer: ((a))

From low potential to high potential

21

Which of the following is an application of the 5S concept in a workshop?

  1. ((a))

    Increasing the number of safety supervisors

  2. ((b))

    Keeping tools and materials organised for easy access

  3. ((c))

    Removing safety protocols to improve efficiency

  4. ((d))

    Using extra tools without proper storage

Show Answer
Answer: ((a))

Increasing the number of safety supervisors

22

Find the value of 96.86572 × 107.

  1. ((a))

    96,86,57,200

  2. ((b))

    0.9686572

  3. ((c))

    96,86,572

  4. ((d))

    9,68,65,720

Show Answer
Answer: ((a))

96,86,57,200

23

Ampere is the SI unit of ________. 

  1. ((a))

    electric current

  2. ((b))

    electric power

  3. ((c))

    electric charge

  4. ((d))

    mass

Show Answer
Answer: ((a))

electric current

24

If a = 21 and b = 19 , find the value of a2+b2+aba3−b3\mathrm{\frac{a ^ 2 + b ^ 2 + ab}{a ^ 3 - b ^ 3}}.

  1. ((a))

    35\frac{3}{5}

  2. ((b))

    23\frac{2}{3}

  3. ((c))

    25\frac{2}{5}

  4. ((d))

    12\frac{1}{2}

Show Answer
Answer: ((a))

35\frac{3}{5}

25

What is the immediate action to take when a fire breaks out in a workplace?

  1. ((a))

    Ignore the fire and continue working

  2. ((b))

    Try to put it out using water without knowing the fire type

  3. ((c))

    Gather near the fire to observe the situation

  4. ((d))

    Raise the alarm and evacuate the area

Show Answer
Answer: ((a))

Ignore the fire and continue working

26

The floor of a rectangular hall is a square with a perimeter of 220 m. If the cost of painting the four walls at the rate of ₹10 per m2 is ₹11,000, then find the volume of the hall.

  1. ((a))

    15,125 m3

  2. ((b))

    19,200 m3

  3. ((c))

    19,520 m3

  4. ((d))

    18,250 m3

Show Answer
Answer: ((a))

15,125 m3

27

The list price of an article is ₹5,000 and a discount of 70% is offered on the list price. What additional discount per cent on the already discounted price must be offered to a customer to bring the net selling price to ₹1,275?

  1. ((a))

    10%

  2. ((b))

    16%

  3. ((c))

    18%

  4. ((d))

    15%

Show Answer
Answer: ((a))

10%

28

Each of I, J, K, L, U, V and W has an exam on a different day of a week starting from Monday and ending on Sunday of the same week.J has the exam on Friday. Only two people have the exam between V and J. Only four people have the exam between L and V. U has the exam immediately after W. K does not have the exam on Monday.How many people have the exam before K and after I?

  1. ((a))

    Three

  2. ((b))

    Four

  3. ((c))

    One

  4. ((d))

    Two

Show Answer
Answer: ((a))

Three

29

The median of the data 2, 6, 4, 8, 1, 2, 5, 8, 9, 10, 12, 9, 7, 8, 3, 1, 0, 9, 2, 5 is ______.

  1. ((a))

    6

  2. ((b))

    5.5

  3. ((c))

    5

  4. ((d))

    6.5

Show Answer
Answer: ((a))

6

30

If an electric heater draws a current of 5 A when the potential difference across its terminals is 75 V, what current will it draw when the potential difference is increased to 150 V?

  1. ((a))

    10 A

  2. ((b))

    15 A

  3. ((c))

    20 A

  4. ((d))

    30 A

Show Answer
Answer: ((a))

10 A

31

Two sets of numbers are given below. In each set of numbers, certain mathematical operation(s) on the first number results in the second number. Similarly, certain mathematical operation(s) on the second number results in the third number and so on. Which of the given options follows the same set of operations as in the given sets?

(NOTE: Operations should be performed on the whole numbers, without breaking down the numbers into their constituent digits. E.g. 13 – Operations on 13 such as adding/subtracting/multiplying to 13 can be performed. Breaking down 13 into 1 and 3 and then performing mathematical operations on 1 and 3 is not allowed.)

11 – 121 – 221 – 171; 27 – 729 – 829 – 779

  1. ((a))

    16 – 196 – 296 – 246

  2. ((b))

    13 – 169 – 244 – 188

  3. ((c))

    25 – 625 – 725 – 675

  4. ((d))

    23 – 529 – 629 – 589

Show Answer
Answer: ((a))

16 – 196 – 296 – 246

32

The HCF of two numbers is 62, and the other two factors of the LCM of these factors are 7 and 9. Which of the options given below can be a possible value of the smaller of the two numbers?

  1. ((a))

    432

  2. ((b))

    434

  3. ((c))

    433

  4. ((d))

    431

Show Answer
Answer: ((a))

432

33

If the sum of lengths of two adjacent sides of a parallelogram is 12 cm, then the perimeter of the parallelogram is: 

  1. ((a))

    34 cm

  2. ((b))

    36 cm

  3. ((c))

    20 cm

  4. ((d))

    24 cm

Show Answer
Answer: ((a))

34 cm

34

How many base units are given in the SI system?

  1. ((a))

    9

  2. ((b))

    7

  3. ((c))

    3

  4. ((d))

    11

Show Answer
Answer: ((a))

9

35

A is thrice as good a workman as B and together they can finish a piece of work in 12 days. In how many days can A alone finish the work?

  1. ((a))

    14 days

  2. ((b))

    12 days

  3. ((c))

    16 days

  4. ((d))

    18 days

Show Answer
Answer: ((a))

14 days

36

Which of the following is NOT one of the 5S principles?

  1. ((a))

    Sustain

  2. ((b))

    Supervise

  3. ((c))

    Standardise

  4. ((d))

    Sort

Show Answer
Answer: ((a))

Sustain

37

Based on the English alphabetical order, three of the following four letter-cluster pairs are alike in a certain way and thus form a group. Which letter-cluster pair DOES NOT belong to that group??

(Note: The odd one out is not based on the number of consonants/vowels or their position in the letter-cluster pair)

  1. ((a))

    DW – YA 

  2. ((b))

    MF – HJ

  3. ((c))

    WP – RS

  4. ((d))

    SL – NP

Show Answer
Answer: ((a))

DW – YA 

38

Which of the following is a poor conductor of heat? 

  1. ((a))

    Wool

  2. ((b))

    Steel spoon

  3. ((c))

    Copper

  4. ((d))

    Aluminium rod

Show Answer
Answer: ((a))

Wool

39

Rakesh starts a business with a capital of ₹2,50,000. He incurs a loss of 5% during the first year. However, he makes a profit of 4% on his remaining investment during the second year. Finally, he makes a profit of 20% on his new capital during the third year. Find his total profit at the end of three years.

  1. ((a))

    ₹46,400

  2. ((b))

    ₹46,500

  3. ((c))

    ₹46,700

  4. ((d))

    ₹46,600

Show Answer
Answer: ((a))

₹46,400

40

The resistances of 30 ohm, 20 ohm and 60 ohm are connected in parallel. The equivalent resistance of the combination is ________. 

  1. ((a))

    110 ohm

  2. ((b))

    0.1 ohm

  3. ((c))

    12 ohm

  4. ((d))

    10 ohm

Show Answer
Answer: ((a))

110 ohm

41

What should come in place of the question mark (?) in the given series?

UT27, RQ25, NM23, ?

  1. ((a))

    IG21

  2. ((b))

    IH29

  3. ((c))

    JH19

  4. ((d))

    IH21

Show Answer
Answer: ((a))

IG21

42

Refer to the following letter, number and symbol series and answer the question that follows. Counting to be done from left to right only.

(Left) K A T & 4 @ Y # 6 K & 2 R % 7 D 3 5 E * S (Right)

How many such symbols are there which are immediately preceded by a number and also immediately followed by a letter?

  1. ((a))

    One 

  2. ((b))

    Three

  3. ((c))

    Two

  4. ((d))

    Four

Show Answer
Answer: ((a))

One 

43

Match the following.

(A) Continuous thick lines(P) Projection lines
(B) Hidden lines(Q) Principal lines
(C) Outlines(R) Dotted lines
(D) Extension lines(S) Object lines
  1. ((a))

    A-S, B-R, C-Q, D-P

  2. ((b))

    A-R, B-S, C-Q, D-P

  3. ((c))

    A-S, B-R, C-P, D-Q

  4. ((d))

    A-P, B-R, C-Q, D-S

Show Answer
Answer: ((a))

A-S, B-R, C-Q, D-P

44

Which of the following is an example of uniform motion? 

  1. ((a))

    A vehicle moving through a crowded area

  2. ((b))

    A train moving at a constant speed on a straight track

  3. ((c))

    A sprinter running a 100-metre race with varying speed

  4. ((d))

    A ball rolling down a slope

Show Answer
Answer: ((a))

A vehicle moving through a crowded area

45

Two sets of numbers are given below. In each set of numbers, certain mathematical operation(s) on the first number results in the second number. Similarly, certain mathematical operation(s) on the second number results in the third number and so on. Which of the given options follows the same set of operations as in the given sets?

(NOTE: Operations should be performed on the whole numbers, without breaking down the numbers into their constituent digits. E.g. 13 – Operations on 13 such as adding/subtracting/multiplying to 13 can be performed. Breaking down 13 into 1 and 3 and then performing mathematical operations on 1 and 3 is not allowed.)

24 – 48 – 108 – 36; 18 – 36 – 96 – 32

  1. ((a))

    82 – 139 – 234 – 78 

  2. ((b))

    132 – 264 – 444 – 138

  3. ((c))

    53 – 106 – 166 – 55

  4. ((d))

    48 – 96 – 156 – 52

Show Answer
Answer: ((a))

82 – 139 – 234 – 78 

46

Match the following, according to lettering and numbering (uppercase lettering) as per BIS SP: 46-2003.

Width (W)Capital letters
(A) 5(I) W
(B) 6(II) A, M, Q, V, X, Y
(C) 7(III) B, D, G, H, K, N, O, P, R, S, T, U and Z
(D) 9(IV) C, E, F, L
  1. ((a))

    A-(I), B-(III), C-(II), D-(IV)

  2. ((b))

    A-(IV), B-(III), C-(II), D-(I)

  3. ((c))

    A-(IV), B-(III), C-(I), D-(II)

  4. ((d))

    A-(IV), B-(II), C-(III), D-(I)

Show Answer
Answer: ((a))

A-(I), B-(III), C-(II), D-(IV)

47

An object of mass m is made to fall freely from a height h. As the object continues to fall, what will happen to its energy?

  1. ((a))

    The kinetic energy and potential energy will not change.

  2. ((b))

    The potential energy would decrease while the kinetic energy would increase.

  3. ((c))

    The potential energy would increase while the kinetic energy would decrease.

  4. ((d))

    The potential energy and kinetic energy will both increase. 

Show Answer
Answer: ((a))

The kinetic energy and potential energy will not change.

48

A can complete a piece of work in 18 days. B can complete it in 14 days. With the assistance of C, they completed the work in 7 days. C alone can complete it in ______________ days. 

  1. ((a))

    63

  2. ((b))

    42

  3. ((c))

    64

  4. ((d))

    36

Show Answer
Answer: ((a))

63

49

What should come in place of the question mark (?) in the given alpha-numeric series?

2M, 5O, 10R, 13T, 18W, 21Y, ?

  1. ((a))

    26B 

  2. ((b))

    26C

  3. ((c))

    24B

  4. ((d))

    26A

Show Answer
Answer: ((a))

26B 

50

The mode of 4, 6, 4, 6, 5, 7, 5, 7, 4, 6, 7, 6 is:

  1. ((a))

    4

  2. ((b))

    6

  3. ((c))

    5

  4. ((d))

    7

Show Answer
Answer: ((a))

4

51

How fast should a cat of mass 15 kg run in order to have a kinetic energy of 120 J?

  1. ((a))

    40 m/s

  2. ((b))

    4 m/s 

  3. ((c))

    16 m/s

  4. ((d))

    0.16 m/s

Show Answer
Answer: ((a))

40 m/s

52

In a certain code language, ‘WILD’ is coded as ‘8164’ and ‘DOGS’ is coded as ‘3517’. What is the code for ‘D’ in the given code language?

  1. ((a))

    4

  2. ((b))

    1

  3. ((c))

    3

  4. ((d))

    5

Show Answer
Answer: ((a))

4

53

Simran rides a distance of 60 m in one minute and then returns along the same straight path. The average velocity of her ride is _____. 

  1. ((a))

    0 m/s 

  2. ((b))

    2 m/s

  3. ((c))

    1 m/s

  4. ((d))

    60 m/s

Show Answer
Answer: ((a))

0 m/s 

54

The resistance of a metallic wire is R. If the radius of the metallic wire is reduced to half of its initial value while keeping all other parameters the same, the new resistance becomes ______.

  1. ((a))

    R4\frac{R}{4}

  2. ((b))

    R2\frac{R}{2}

  3. ((c))

    2R

  4. ((d))

    4R

Show Answer
Answer: ((a))

R4\frac{R}{4}

55

Select the pair that follows the same pattern as the one followed by the two sets of pairs given below. Both pairs follow the same pattern.

BSR : GQW

LOB : QMG

  1. ((a))

    RWH : WUM

  2. ((b))

    HVD : LTH

  3. ((c))

    KRW : NPZ

  4. ((d))

    QGT : TDW

Show Answer
Answer: ((a))

RWH : WUM

56

If 11.6 : x :: x : 2.9, and x > 0, then find the value of x. 

  1. ((a))

    10.9

  2. ((b))

    7.7

  3. ((c))

    5.8

  4. ((d))

    3.1

Show Answer
Answer: ((a))

10.9

57

What is the first step when encountering a system failure in a workplace?

  1. ((a))

    Report the issue and follow the emergency protocol

  2. ((b))

    Ignore the failure and continue working

  3. ((c))

    Immediately restart all systems without inspection

  4. ((d))

    Disconnect all power sources permanently

Show Answer
Answer: ((a))

Report the issue and follow the emergency protocol

58

What should come in place of the question mark (?) in the given series?

87 118 149 ? 211 242

  1. ((a))

    188

  2. ((b))

    171

  3. ((c))

    180

  4. ((d))

    199

Show Answer
Answer: ((a))

188

59

Jaspreet deposited a sum of ₹12,800 at 5% rate of interest per annum, compounded annually. The total amount (in ₹) received by Jaspreet after 2 years will be: 

  1. ((a))

    13,997

  2. ((b))

    14,112

  3. ((c))

    14,512

  4. ((d))

    14,442

Show Answer
Answer: ((a))

13,997

60

Which key combination is commonly used for copying text in many text editing applications in Windows?

  1. ((a))

    Ctrl+V

  2. ((b))

    Ctrl+S

  3. ((c))

    Ctrl+C

  4. ((d))

    Tab 

Show Answer
Answer: ((a))

Ctrl+V

61

How many significant figures are there in 4.700 m? 

  1. ((a))

    3

  2. ((b))

    1

  3. ((c))

    2

  4. ((d))

    4

Show Answer
Answer: ((a))

3

62

In a business, Tushar invests in ₹10,000 and Salil invests in ₹20,000. Tushar received 10% of the profit for managing the business and the rest of the profit is divided in the ratio of their capitals. Find Tushar's share of the profit (in ₹) in a profit of ₹14,400.

  1. ((a))

    5,610

  2. ((b))

    5,760

  3. ((c))

    5,510

  4. ((d))

    5,910

Show Answer
Answer: ((a))

5,610

63

Which of the following correctly describes the role of DNS (Domain Name System) in internet architecture? 

  1. ((a))

    DNS routes data packets to their destination across the internet.

  2. ((b))

    DNS translates domain names into IP addresses to allow browsers to locate web servers.

  3. ((c))

    DNS translates IP addresses into domain names to make them easier to remember.

  4. ((d))

    DNS secures the data transmitted over the internet by encrypting it.

Show Answer
Answer: ((a))

DNS routes data packets to their destination across the internet.

64

Which of the following is an INCORRECT formula for power?

  1. ((a))

    VI

  2. ((b))

    I2R

  3. ((c))

    I2Rt

  4. ((d))

    V2/R

Show Answer
Answer: ((a))

VI

65

A boy goes to school at a speed of 5 km/hr. He returns at a speed of 14 km/hr. He takes a total of 8 hours for both going to school and returning. The distance (in km) between his home and school is:

  1. ((a))

    29.5

  2. ((b))

    27

  3. ((c))

    28.6

  4. ((d))

    31

Show Answer
Answer: ((a))

29.5

66

Which of the following features allows the user to quickly find emails received from a specific sender?

  1. ((a))

    Archive

  2. ((b))

    Draft

  3. ((c))

    Filter

  4. ((d))

    Sort 

Show Answer
Answer: ((a))

Archive

67

If ‘A’ stands for ‘÷’, ‘B’ stands for ‘×’, ‘C’ stands for ‘+’ and ‘D’ stands for ‘−’, then what will come in place of the question mark (?) in the following equation?

35 A 7 C 9 B 3 D 16 = ?

  1. ((a))

    21

  2. ((b))

    18

  3. ((c))

    16

  4. ((d))

    10

Show Answer
Answer: ((a))

21

68

What is the main function of the Transport Layer in the internet architecture?

  1. ((a))

    Reliable data transfer and error correction

  2. ((b))

    Data encapsulation

  3. ((c))

    Routing of packets

  4. ((d))

    IP addressing

Show Answer
Answer: ((a))

Reliable data transfer and error correction

69

A line in an engineering drawing is the ____________.

  1. ((a))

    one-dimensional figure, which has length but no width

  2. ((b))

    dimensionless location in space or on a drawing sheet that has no width, height, or depth

  3. ((c))

    three-dimensional object with length, breadth, and height

  4. ((d))

    closed curve where all points are the same distance from a fixed centre point

Show Answer
Answer: ((a))

one-dimensional figure, which has length but no width

70

The heat developed in a 5 ohm resistor in 2 minutes when a 2A current passes through it is ________. 

  1. ((a))

    2400 J 

  2. ((b))

    500 J 

  3. ((c))

    1000 J

  4. ((d))

    40 J

Show Answer
Answer: ((a))

2400 J 

71

The areas of three adjacent faces of a solid cuboid are 162 cm2, 144 cm2 and 50 cm2. What is the volume (in cm3) of the cuboid?

  1. ((a))

    1080 

  2. ((b))

    805

  3. ((c))

    833

  4. ((d))

    1365

Show Answer
Answer: ((a))

1080 

72

Pihu starts her car at 9 a.m. to reach her office, which is 20 km away. She covers the first 10 km in 30 minutes and reaches her office at 10 a.m. Pihu’s motion is ________. 

  1. ((a))

    retarded motion

  2. ((b))

    non-uniform motion

  3. ((c))

    accelerated motion

  4. ((d))

    uniform motion 

Show Answer
Answer: ((a))

retarded motion

73

How does turning off unused electrical devices contribute to energy conservation?

  1. ((a))

    By lowering utility bills

  2. ((b))

    By enhancing device performance

  3. ((c))

    By degrading electrical devices

  4. ((d))

    By increasing energy use

Show Answer
Answer: ((a))

By lowering utility bills

74

An electric lamp with a resistance of 35 ohms and a conductor with a resistance of 5 ohms are connected to an 8 V battery in series. Calculate the current flowing through the circuit. 

  1. ((a))

    0.2 A

  2. ((b))

    1.82 A

  3. ((c))

    40 A 

  4. ((d))

    2 A

Show Answer
Answer: ((a))

0.2 A

75

Calculate the energy possessed by an object of mass 10 kg when it is raised to a height of 5 m from the ground. Given: g = 9.8 m s-2.

  1. ((a))

    500 J 

  2. ((b))

    450 J

  3. ((c))

    490 J

  4. ((d))

    400 J

Show Answer
Answer: ((a))

500 J 

76

If sinθ+cosθsinθ−cosθ=12\mathrm{\frac{sin \theta+cos\theta}{sin\theta-cos\theta}=12} then the value of 121tan2θ−3169Cot2θ+1\frac{121tan^2\theta - 3}{169Cot^2\theta + 1} is:

  1. ((a))

    −8321-\frac{83}{21}

  2. ((b))

    −8361-\frac{83}{61}

  3. ((c))

    8361\frac{83}{61}

  4. ((d))

    8321\frac{83}{21}

Show Answer
Answer: ((a))

−8321-\frac{83}{21}

77

E, F, G, H, P, Q, and R, are sitting around a circular table facing the centre. F sits fourth to the right of E. Only R sits between F and H. H is NOT an immediate neighbour of E. Only P sits between E and G.

How many people sit between G and Q when counted from the right of G?

  1. ((a))

    Two

  2. ((b))

    Three

  3. ((c))

    Four 

  4. ((d))

    One

Show Answer
Answer: ((a))

Two

78

Find the value of x2 + y2 , given that, x = 7 + √1, y = 7 − √1.

  1. ((a))

    56

  2. ((b))

    69

  3. ((c))

    100

  4. ((d))

    98

Show Answer
Answer: ((a))

56

79

How do we find absolute error?

  1. ((a))

    Absolute error = Actual value/observed value

  2. ((b))

    Absolute error = Actual value × observed value

  3. ((c))

    Absolute error = Actual value + observed value

  4. ((d))

    Absolute error = Actual value − observed value

Show Answer
Answer: ((a))

Absolute error = Actual value/observed value

80

What is the main advantage of using solar energy over fossil fuels? 

  1. ((a))

    Greenhouse gas emission is higher when solar energy is used.

  2. ((b))

    Solar energy extraction requires high operational cost when compared to fossil fuels.

  3. ((c))

    Solar energy requires mining and extraction, whereas fossil fuels are free of cost.

  4. ((d))

    Solar energy is abundantly available and renewable in nature.

Show Answer
Answer: ((a))

Greenhouse gas emission is higher when solar energy is used.

81

Which of the following is an effective way to prevent electrical accidents in the workplace?

  1. ((a))

    Working on live wires with bare hands

  2. ((b))

    Using water to cool overheated electrical equipment

  3. ((c))

    Using insulated tools and wearing rubber gloves

  4. ((d))

    Ignoring minor electrical faults

Show Answer
Answer: ((a))

Working on live wires with bare hands

82

Which term describes the maximum amount of solar energy that a photovoltaic (PV) system can convert into electricity under standard test conditions?

  1. ((a))

    Nameplate capacity

  2. ((b))

    Rated capacity

  3. ((c))

    Effective capacity

  4. ((d))

    Peak load

Show Answer
Answer: ((a))

Nameplate capacity

83

Aditya is using two thin blankets instead of one thick blanket in winter to keep himself warm because ________.

  1. ((a))

    the friction between the two blankets produces heat

  2. ((b))

    the air trapped between the blankets is a poor conductor of heat

  3. ((c))

    the blankets are at a higher temperature than the surroundings

  4. ((d))

    two blankets are cheaper than one thick blanket

Show Answer
Answer: ((a))

the friction between the two blankets produces heat

84

In a certain code language, ‘BORE’ is coded as ‘8624’ and ‘TABS’ is coded as ‘3217’. What is the code for ‘B’ in the given code language?

  1. ((a))

    7

  2. ((b))

    1

  3. ((c))

    2

  4. ((d))

    8

Show Answer
Answer: ((a))

7

85

Two trains of lengths 155 m and 160 m are running at speeds of 74 km/hr and 52 km/hr, respectively, on parallel tracks in opposite directions. In how many seconds will they pass each other? 

  1. ((a))

    9 seconds

  2. ((b))

    14 seconds

  3. ((c))

    7 seconds

  4. ((d))

    18 seconds

Show Answer
Answer: ((a))

9 seconds

86

In winters, people wear jacket because _____. 

  1. ((a))

    it looks good

  2. ((b))

    fabric of jacket is a conductor of heat so it traps body heat

  3. ((c))

    fabric of jacket is an insulator of heat so it traps body heat

  4. ((d))

    jacket allows the heat to flow from our body to surroundings

Show Answer
Answer: ((a))

it looks good

87

Akshay gets 2% increase in his sale amount in the first year and 25% in the second year. With that his present sale is ₹1,42,800. What was his sale (in ₹) two years ago? 

  1. ((a))

    1,14,240

  2. ((b))

    92,000

  3. ((c))

    1,40,000

  4. ((d))

    1,12,000

Show Answer
Answer: ((a))

1,14,240

88

What is the scientific notation for 55,60,000 km?

  1. ((a))

    5.56 × 106 km

  2. ((b))

    5.56 × 104 km

  3. ((c))

    55.6 × 104 km

  4. ((d))

    556 × 106 km

Show Answer
Answer: ((a))

5.56 × 106 km

89

Two containers, one painted black and the other painted white, have been kept in sunlight for one hour in the afternoon. Choose the correct observation.

  1. ((a))

    There is no effect on either container.

  2. ((b))

    The white container becomes hotter than the black container.

  3. ((c))

    The black container becomes hotter than the white container.

  4. ((d))

    Both containers become equally hot.

Show Answer
Answer: ((a))

There is no effect on either container.

90

The energy possessed by an object by virtue of its motion is known as ________. 

  1. ((a))

    kinetic energy

  2. ((b))

    potential energy

  3. ((c))

    heat energy

  4. ((d))

    light energy

Show Answer
Answer: ((a))

kinetic energy

91

Two sets of numbers are given below. In each set of numbers, certain mathematical operation(s) on the first number results in the second number. Similarly, certain mathematical operation(s) on the second number results in the third number and so on. Which of the given options follows the same set of operations as in the given sets?

(NOTE: Operations should be performed on the whole numbers, without breaking down the numbers into their constituent digits. E.g. 13 – Operations on 13 such as adding/subtracting/multiplying to 13 can be performed. Breaking down 13 into 1 and 3 and then performing mathematical operations on 1 and 3 is not allowed.)

4 – 8 – 18 – 9

6 – 12 – 22 – 11

  1. ((a))

    8 – 16 – 26 – 13

  2. ((b))

    3 – 15 – 12 – 20

  3. ((c))

    9 – 18 – 28 – 20

  4. ((d))

    11 – 13 – 22 – 63

Show Answer
Answer: ((a))

8 – 16 – 26 – 13

92

Which of the following is the temperature range in a clinical thermometer?

  1. ((a))

    30°C to 43°C

  2. ((b))

    35°C to 42°C

  3. ((c))

    10°C to 45°C

  4. ((d))

    31°C to 44°C

Show Answer
Answer: ((a))

30°C to 43°C

93

Which of the following groups represents conductors of heat?

  1. ((a))

    Wood, paper, silver

  2. ((b))

    Paper, copper, plastic

  3. ((c))

    Aluminium, silver, copper

  4. ((d))

    Aluminium, plastic, wood

Show Answer
Answer: ((a))

Wood, paper, silver

94

Select the triad that follows the same pattern as that followed by the two triads given below. Both triads follow the same pattern.

JK - LM - NO

TU - VW - XY

  1. ((a))

    DE - FG - HI

  2. ((b))

    DE - FG - KL

  3. ((c))

    WE - DF - HI

  4. ((d))

    DE - FB - DF

Show Answer
Answer: ((a))

DE - FG - HI

95

In Engineering Drawing, principal lines are drawn to represent __________.

  1. ((a))

    interior or hidden edges

  2. ((b))

    axes of cylindrical, conical or spherical objects

  3. ((c))

    visible edges and surface boundaries of objects

  4. ((d))

    wide lines along which the prints are trimmed

Show Answer
Answer: ((a))

interior or hidden edges

96

A fruit seller had some apples. He sells 40% of the apples and now has 900 apples. How many apples did he originally have?

  1. ((a))

    1800

  2. ((b))

    2250

  3. ((c))

    1500

  4. ((d))

    1350

Show Answer
Answer: ((a))

1800

97

Based on the English alphabetical order, three of the following four letter-cluster pairs are alike in a certain way and thus form a group. Which letter-cluster pair DOES NOT belong to that group?

(Note: The odd one out is not based on the number of consonants/vowels or their position in the letter-cluster pair.)

  1. ((a))

    SA – WQ

  2. ((b))

    WE – AU

  3. ((c))

    DL – HB

  4. ((d))

    MU – QL 

Show Answer
Answer: ((a))

SA – WQ

98

Which of the following represents an item with kinetic energy? 

  1. ((a))

    An extended rubber band

  2. ((b))

    A stone in motion

  3. ((c))

    A book resting on a table

  4. ((d))

    A compressed spring

Show Answer
Answer: ((a))

An extended rubber band

99

In a certain code language,

'A × B' means ‘A is the son of B’,

'A − B' means ‘A is the brother of B’,

'A + B' means ‘A is the wife of B’ and

'A % B' means ‘A is the father of B’.

How is M related to T if ‘M × N % P + S − T’?

  1. ((a))

    Brother's wife's brother

  2. ((b))

    Brother's wife's father

  3. ((c))

    Brother's wife's father's brother

  4. ((d))

    Brother's wife's father's father 

Show Answer
Answer: ((a))

Brother's wife's brother

100

A person saves 50% of his income. If his expenditure is ₹640, then his income (in ₹) is: 

  1. ((a))

    600

  2. ((b))

    1,320

  3. ((c))

    560

  4. ((d))

    1,280

Show Answer
Answer: ((a))

600

Part B (75 questions)

101

_________________ recommend(s) 20 mm wide margins for sheet sizes AO and A1 in engineering drawings. 

  1. ((a))

    Custom grids 

  2. ((b))

    Geographic coordinate systems

  3. ((c))

    Borders and frames: SP: 46 (2003)

  4. ((d))

    Grid reference system

Show Answer
Answer: ((a))

Custom grids 

102

How many divisions are there on a vernier scale as used in a modern vernier caliper for metric measurement? 

  1. ((a))

    100

  2. ((b))

    25

  3. ((c))

    75

  4. ((d))

    50

Show Answer
Answer: ((a))

100

103

Which of the following locations is correct for installing the oil filter in the engine? 

  1. ((a))

    After lines going to supply the oil to the bearing after coolers 

  2. ((b))

    Up stream of coolers in order to filter if any solid part from coolers lives the oil lines

  3. ((c))

    In between coolers and the oil lines coming from sump 

  4. ((d))

    Downstream of coolers in order to filter if any solid part from coolers enters the oil lines 

Show Answer
Answer: ((a))

After lines going to supply the oil to the bearing after coolers 

104

_______ is a type of single thin sheet of metal that yields when pressure is applied and is widely used in most modern cars. When pressure is removed, the metal springs back to its original shape. 

  1. ((a))

    Cushion spring 

  2. ((b))

    Spiral spring

  3. ((c))

     Leaf spring

  4. ((d))

    Diaphragm spring 

Show Answer
Answer: ((a))

Cushion spring 

105

The rotors in a roots air-blower type supercharger are designed in which geometric shape? 

  1. ((a))

    Spiral shape

  2. ((b))

    Cylindrical shape

  3. ((c))

    Epicycloid shape 

  4. ((d))

    Helical shape

Show Answer
Answer: ((a))

Spiral shape

106

Which of the following components in the axle is the most likely to fail if there is an unusual loud clanking or clunking as you put your vehicle into gear, or if a vehicle seems to struggle to get power as it starts to move? 

  1. ((a))

    Bending in the shaft induced 

  2. ((b))

    There is a crack initiated in the axle at cross sectional area perpendicular to axis

  3. ((c))

     Axle-joint damage

  4. ((d))

     Bearing at the wheel is damaged

Show Answer
Answer: ((a))

Bending in the shaft induced 

107

Which of the following materials is used as a binding agent in organic brake linings?

  1. ((a))

    Metal powder

  2. ((b))

    Resin 

  3. ((c))

    Cotton

  4. ((d))

    Rubber

Show Answer
Answer: ((a))

Metal powder

108

Which of the following terms is associated with the cams that control the valves and directly influence the breathing process of the engine? 

  1. ((a))

    Material of construction of the cams 

  2. ((b))

    Shape and timing of the cams 

  3. ((c))

    Speed of the cams

  4. ((d))

    Location and length of the cams 

Show Answer
Answer: ((a))

Material of construction of the cams 

109

A type of brake has a diaphragm operating in a cylinder. For application of brakes on one side, a diaphragm is subjected to atmospheric pressure while the other is applied negative pressure by exhausting air known as _____ brake. 

  1. ((a))

    vacuum

  2. ((b))

    hydraulic

  3. ((c))

    air

  4. ((d))

    electric

Show Answer
Answer: ((a))

vacuum

110

In the combustion process, electronically managed fuel injection systems control combustion by:  

  1. ((a))

    eliminating the need for oxygen 

  2. ((b))

    decreasing fuel atomisation 

  3. ((c))

    controlling the air-fuel ratio using sensors and catalytic converters

  4. ((d))

    increasing unburnt fuel emissions 

Show Answer
Answer: ((a))

eliminating the need for oxygen 

111

Which of the statements is correct about a compression ignition engine? 

  1. ((a))

    Initial and maintenance costs of diesel engine is less compared to petrol engine.

  2. ((b))

    Operating speed range is less compared to petrol engine.

  3. ((c))

    Diesel engine produces less noise compared to petrol engine.  

  4. ((d))

    Starting is easy for diesel engine since less cranking effort is required compared to petrol engine. 

Show Answer
Answer: ((a))

Initial and maintenance costs of diesel engine is less compared to petrol engine.

112

Which of the following stages of an automatic transmission system locks the transmission, restricting a vehicle from moving? 

  1. ((a))

    Low (L) stage  

  2. ((b))

    Neutral (N) stage 

  3. ((c))

    Drive (D) stage 

  4. ((d))

    Park (P) stage 

Show Answer
Answer: ((a))

Low (L) stage  

113

Which of the following actions is a part of the emergency response team's responsibilities during an active emergency? 

  1. ((a))

    Rescuing persons in immediate danger

  2. ((b))

    Conducting routine safety checks 

  3. ((c))

    Preparing reports on emergency incidents

  4. ((d))

    Scheduling regular evacuation drills

Show Answer
Answer: ((a))

Rescuing persons in immediate danger

114

Which of the following is a primary difference between a primary and a secondary electrochemical cell? 

  1. ((a))

    A primary cell cannot be recharged, while a secondary cell can be recharged. 

  2. ((b))

    A secondary cell produces more energy than a primary cell.

  3. ((c))

    A primary cell can be recharged, while a secondary cell cannot be recharged.

  4. ((d))

    There is no difference between primary and secondary cells

Show Answer
Answer: ((a))

A primary cell cannot be recharged, while a secondary cell can be recharged. 

115

In a logic circuit, three SPST (Single Pole Single Throw) switches are used to implement a logic gate. The switches are connected in series. What is the output of the circuit if all switches are closed? 

  1. ((a))

    Undefined

  2. ((b))

    The output will depend on the type of gate used

  3. ((c))

    1

  4. ((d))

    0

Show Answer
Answer: ((a))

Undefined

116

A 100-mm centre-punch could have a 10-mm diameter body and a 6-mm diameter point ground to an angle of _________. 

  1. ((a))

     30°

  2. ((b))

    120° 

  3. ((c))

    90° 

  4. ((d))

    60° 

Show Answer
Answer: ((a))

 30°

117

What is the primary purpose of preventive maintenance? 

  1. ((a))

     To eliminate the need for regular inspections 

  2. ((b))

    To delay repairs until breakdowns occur  

  3. ((c))

    To reduce unexpected equipment failures 

  4. ((d))

    To increase the workload of employees 

Show Answer
Answer: ((a))

 To eliminate the need for regular inspections 

118

Which of the following statements is NOT correct about the procedure of calculating balancing of crankshaft of an engine?

  1. ((a))

    It involves determining the balancing couple and counterweight mass required to balance the crankshaft. 

  2. ((b))

    To balance a crankshaft, metal can be removed by drilling holes on the 'heavy' side until balance is achieved. 

  3. ((c))

     Crankshaft balancing involves calculating the rotating and reciprocating masses of a crankshaft. 

  4. ((d))

    To balance a crankshaft, metal can be added by welding material deposition on the 'heavy' side until balance is achieved.

Show Answer
Answer: ((a))

It involves determining the balancing couple and counterweight mass required to balance the crankshaft. 

119

The function of a steering system is to convert the rotary movement of the steering wheel into: 

  1. ((a))

    angular turn of the front wheels 

  2. ((b))

    angular turns of the rear wheels

  3. ((c))

    angular velocity of the front wheels 

  4. ((d))

    linear motion of the front wheels 

Show Answer
Answer: ((a))

angular turn of the front wheels 

120

The accuracy of measurement by a try square is about:

  1. ((a))

    0.02 mm per 10 mm length

  2. ((b))

    0.001 mm per 10 mm length 

  3. ((c))

    0.004 mm per 10 mm length

  4. ((d))

    0.002 mm per 10 mm length 

Show Answer
Answer: ((a))

0.02 mm per 10 mm length

121

Which of the following conversions are correct?

  1. ((a))

    1000 L = 1 dm3 and 1 mL = 1000 cm3

  2. ((b))

    1 L = 1000 dm3 and 1 mL = 1000 cm3 

  3. ((c))

    1 L = 1 dm3 and 1 mL = 1 cm3

  4. ((d))

    1000 L = 1 dm3 and 1000 mL = 1 cm3

Show Answer
Answer: ((a))

1000 L = 1 dm3 and 1 mL = 1000 cm3

122

Which of the following statements is NOT correct about the parts associated with the cylinder head?

  1. ((a))

    The fuel injector is used to spray fuel into the engine cylinder. It is fixed to the cylinder head. 

  2. ((b))

    Space enclosed between the cylinder head and piston top during combustion is the combustion chamber

  3. ((c))

    The combustion of fuel and the consequent release of thermal energy results in the building up of pressure in the casing. 

  4. ((d))

    Through the metal screw the spark plug is fitted in the cylinder head plug

Show Answer
Answer: ((a))

The fuel injector is used to spray fuel into the engine cylinder. It is fixed to the cylinder head. 

123

What is the function of the drive end frame in an alternator?

  1. ((a))

    Regulating voltage output of the alternator

  2. ((b))

    Supporting a pre-lubricated sealed bearing for rotor shaft rotation. 

  3. ((c))

    Acting as the main power storage unit

  4. ((d))

     Controlling the current flow to the battery. 

Show Answer
Answer: ((a))

Regulating voltage output of the alternator

124

Which of the following statements is NOT correct about the functions of a lube oil pump? 

  1. ((a))

    Maintains consistent oil circulation throughout the engine. 

  2. ((b))

    Provides direction for the oil’s passage through the galleries and to various areas. 

  3. ((c))

    Oil is transferred to the engine’s key components under high pressure,.

  4. ((d))

    The movement of engine lubricant around the engine is made difficult 

Show Answer
Answer: ((a))

Maintains consistent oil circulation throughout the engine. 

125

Which of the following types of piston ring is placed at the top of the piston in an IC engine? 

  1. ((a))

    Oil ring

  2. ((b))

    Compression ring 

  3. ((c))

    Wiper ring

  4. ((d))

    Pressure ring 

Show Answer
Answer: ((a))

Oil ring

126

When the crank is at the dead centre, what will be the magnitude of bending moment and twisting moment at the crankshaft?

  1. ((a))

    Both bending moment and twisting moment on the shaft are maximum

  2. ((b))

    Bending moment on the shaft is maximum and the twisting moment is zero. 

  3. ((c))

    Bending moment on the shaft is minimum and the twisting moment is maximum. 

  4. ((d))

    Both bending moment and the twisting moment are zero in the shaft

Show Answer
Answer: ((a))

Both bending moment and twisting moment on the shaft are maximum

127

Diesel fuel is generally used in which of the following types of vehicles?

  1. ((a))

    Scooters

  2. ((b))

    Heavy trucks and buses

  3. ((c))

    Aerospace vehicles 

  4. ((d))

    Cars

Show Answer
Answer: ((a))

Scooters

128

What is the primary purpose of shielding in electrical cables?

  1. ((a))

    To protect the cable from external electromagnetic interference

  2. ((b))

    To increase the voltage capacity of the cable

  3. ((c))

    To increase the current-carrying capacity of the cable

  4. ((d))

    To prevent heat loss from the cable

Show Answer
Answer: ((a))

To protect the cable from external electromagnetic interference

129

What happens to the fuel in a vehicle left in the sun?

  1. ((a))

     It decomposes into water and carbon dioxide 

  2. ((b))

    It solidifies  

  3. ((c))

    It becomes more efficient

  4. ((d))

     It evaporates from the tank 

Show Answer
Answer: ((a))

 It decomposes into water and carbon dioxide 

130

Which of the following is a major risk associated with fuel spillage?

  1. ((a))

    Increased productivity

  2. ((b))

    Better lubrication for workshop floors

  3. ((c))

    Reduced need for ventilation

  4. ((d))

    Fire hazards and environmental contamination

Show Answer
Answer: ((a))

Increased productivity

131

Which of the following components is a part of a diesel engine only? 

  1. ((a))

    Spray nozzle

  2. ((b))

    Carburetor

  3. ((c))

    Fuel tank 

  4. ((d))

    Spark plug 

Show Answer
Answer: ((a))

Spray nozzle

132

Natural rubber is soft at high temperatures and brittle at low temperatures; hence raw rubber is heated with sulphur and other additives at a temperature range between 373 – 415 K to make it strong. This process is called ______ of rubber. 

  1. ((a))

    latex

  2. ((b))

    vulcanisation

  3. ((c))

    molding

  4. ((d))

    extrusion

Show Answer
Answer: ((a))

latex

133

What is the primary reason for the heating effect in a conductor when an electric current passes through it?

  1. ((a))

    The electric field in the conductor causes heat generation. 

  2. ((b))

    The movement of protons causes heat generation

  3. ((c))

    The conductor absorbs heat from the surrounding environment. 

  4. ((d))

    The movement of electrons causes heat generation.

Show Answer
Answer: ((a))

The electric field in the conductor causes heat generation. 

134

 4 Which of the following types of brakes can be used with drum, disc or a combination, with air pressure providing the power instead of hydraulic fluid? 

  1. ((a))

    Electric brakes

  2. ((b))

    Magnetic brakes

  3. ((c))

    Pneumatic brakes

  4. ((d))

     Air brakes 

Show Answer
Answer: ((a))

Electric brakes

135

Which of the following is INCORRECT about line standard?

  1. ((a))

    More accurate due to line thickness

  2. ((b))

    Used to measure the distance between two engraved lines

  3. ((c))

    Quick measurements over a wide range 

  4. ((d))

     Subject to parallax error 

Show Answer
Answer: ((a))

More accurate due to line thickness

136

What is the primary function of an alternator in a modern vehicle? 

  1. ((a))

    Storing electrical energy for later use 

  2. ((b))

    Supplying power directly to the spark plugs

  3. ((c))

    Generating Alternating Current (AC) and converting it into Direct Current (DC)

  4. ((d))

    Controlling the fuel injection system

Show Answer
Answer: ((a))

Storing electrical energy for later use 

137

 The space enclosed in the upper part of a cylinder, by the cylinder head and the piston top, during the combustion process is called: 

  1. ((a))

    combustion chamber 

  2. ((b))

     air suction zone 

  3. ((c))

    fuel digestion chamber 

  4. ((d))

    compression ratio

Show Answer
Answer: ((a))

combustion chamber 

138

A rectangular floor measuring 10 m × 8 m is to be tiled. If each tile covers 0.25 m², how many tiles are needed?

  1. ((a))

    320

  2. ((b))

    300

  3. ((c))

    200

  4. ((d))

    250

Show Answer
Answer: ((a))

320

139

Which of the following care and maintenance of a marking table is INCORRECT?

  1. ((a))

    The marking table should be protected from rust. 

  2. ((b))

     After use, the marking table should be cleaned with a soft cloth. 

  3. ((c))

    The marking table should be protected from damage.

  4. ((d))

    The surface of the marking table should not be given a thin layer of oil. 

Show Answer
Answer: ((a))

The marking table should be protected from rust. 

140

For which of the following calipers, a screw and nut are provided for opening and closing the caliper legs? 

  1. ((a))

    Leg and point calipers 

  2. ((b))

    Spring joint calipers

  3. ((c))

    Simple calipers  

  4. ((d))

    Firm joint calipers 

Show Answer
Answer: ((a))

Leg and point calipers 

141

Sine bars are used when a high degree of accuracy less than _________ is needed for measuring angles.

  1. ((a))

    1 degree

  2. ((b))

    30 minutes

  3. ((c))

    30 degrees 

  4. ((d))

    1 minute

Show Answer
Answer: ((a))

1 degree

142

The catalytic converter helps to convert unburnt hydrocarbons into:

  1. ((a))

    carbon monoxide and water 

  2. ((b))

    pure oxygen 

  3. ((c))

     carbon dioxide and water 

  4. ((d))

    nitrogen oxides 

Show Answer
Answer: ((a))

carbon monoxide and water 

143

The primary function of the preliminary strainer is to remove:

  1. ((a))

    water from the fuel 

  2. ((b))

    only the finest particles from the fue

  3. ((c))

    coarser impurities from the fuel 

  4. ((d))

    air from the fuel 

Show Answer
Answer: ((a))

water from the fuel 

144

The process of aligning a principal inertia axis with the geometric axis of rotation of the shaft through the addition or removal of material in a shaft is known as:

  1. ((a))

    equilibrium

  2. ((b))

     parallel alignment 

  3. ((c))

    angular alignment

  4. ((d))

    balancing

Show Answer
Answer: ((a))

equilibrium

145

Which of the following is NOT the correct statement when fitting rings in an internal combustion (IC) engine? 

  1. ((a))

    Cleaning the piston head sealing surface area thoroughly is required. 

  2. ((b))

    Use of specialised tools to install the rings without twisting or damaging them is essential

  3. ((c))

     This is vital for maintaining proper combustion pressure and preventing oil consumption issues.

  4. ((d))

    The most crucial precaution is to ensure proper ring gap and alignment by carefully checking the end gap of each ring. 

Show Answer
Answer: ((a))

Cleaning the piston head sealing surface area thoroughly is required. 

146

 In contexts such as automotive clutches, the spring is used to absorb shock during engagement. It is often referred to as a:

  1. ((a))

    leaf spring of circular shape

  2. ((b))

    cushion spring in flat shape

  3. ((c))

     tensile spring in helical shape 

  4. ((d))

    spiral spring of rectangular shape 

Show Answer
Answer: ((a))

leaf spring of circular shape

147

The main function of an Electronic Control Unit (ECU) is to:

  1. ((a))

    store air in the engine

  2. ((b))

    receive data from sensors and control actuators

  3. ((c))

    store fuel in the engine

  4. ((d))

    work as a battery backup

Show Answer
Answer: ((a))

store air in the engine

148

Which of the following processes is carried out on connecting rods to locate the two halves relative to one another?

  1. ((a))

    Mirror finishing is done by diamond turning machine

  2. ((b))

    Serrations are used 

  3. ((c))

    Dimples are created on the surface

  4. ((d))

    Tapper threads are used 

Show Answer
Answer: ((a))

Mirror finishing is done by diamond turning machine

149

The clutch slave cylinder disengages the clutch from the engine by moving the:

  1. ((a))

     pressure plate 

  2. ((b))

    cushion spring 

  3. ((c))

    leaf spring

  4. ((d))

     spline shaft 

Show Answer
Answer: ((a))

 pressure plate 

150

The accuracy of the dial bore gauge instrument depends on which of the following parts?

  1. ((a))

    A pointer on a graduated dial 

  2. ((b))

     A dot indicator on a linear scale

  3. ((c))

    A marking on a logarithmic dial

  4. ((d))

    An arrow on a semi-circular scale

Show Answer
Answer: ((a))

A pointer on a graduated dial 

151

Match the following designations of sheets with their respective trimmed sizes in length and breadth.

Designation Trimmed Size

A) A0 P) 297 × 420

B) A1 Q) 420 × 594

C) A2 R) 594 × 841

D) A3 S) 841 × 1189

  1. ((a))

    A-P ; B-R ; C-Q ; D-S 

  2. ((b))

    A-S ; B-P ; C-Q ; D-R 

  3. ((c))

     A-Q ; B-R ; C-S ; D-P

  4. ((d))

    A-S ; B-R ; C-Q ; D-P 

Show Answer
Answer: ((a))

A-P ; B-R ; C-Q ; D-S 

152

What is the term used to describe programs that distinguish between uppercase and lowercase letters, treating "yes" and "YES" as different inputs? 

  1. ((a))

    Numerical

  2. ((b))

    Case-sensitive 

  3. ((c))

    Case-insensitive

  4. ((d))

    Alphabetical

Show Answer
Answer: ((a))

Numerical

153

Which of the following statements is/are true about Non-Functional Dimensions (NF) in engineering drawing?

Statement 1: Non-functional Dimensions are shown without limits, as they do not affect the functionality of the component or space.

Statement 2: Non-Functional Dimensions are typically used for reference purposes only, and do not impact the assembly or performance of the component or space.

  1. ((a))

    Only statement 1 is true 

  2. ((b))

    Neither statement is true 

  3. ((c))

    Only statement 2 is true

  4. ((d))

    Both statements are true

Show Answer
Answer: ((a))

Only statement 1 is true 

154

A statement and conclusion for pictorial drawing are given below. Determine the logical relationship between them.

Statement: Pictorial drawings are three-dimensional and provide a visual representation of an object.

Conclusion: Therefore, pictorial drawings are useful for describing the shape of a piece part or component.

  1. ((a))

    The conclusion does not logically follow from the statement. 

  2. ((b))

    The conclusion is unrelated to the statement.

  3. ((c))

    The conclusion logically follows from the statement.

  4. ((d))

    The conclusion is partially supported by the statement.

Show Answer
Answer: ((a))

The conclusion does not logically follow from the statement. 

155

Which option shows the correct answer when 27°C is converted to the kelvin scale?

  1. ((a))

    246 K  

  2. ((b))

    – 246 K 

  3. ((c))

    300 K 

  4. ((d))

    – 300 K

Show Answer
Answer: ((a))

246 K  

156

In a star-type paper filter insert, the fuel flows: 

  1. ((a))

    radially from outside to inside

  2. ((b))

    axially from top to bottom

  3. ((c))

    in a circular motion 

  4. ((d))

     from inside to outside

Show Answer
Answer: ((a))

radially from outside to inside

157

The boiling point of water in a cooling system can be raised by: 

  1. ((a))

    increasing the system pressure

  2. ((b))

    removing water from the system

  3. ((c))

    decreasing the system pressure

  4. ((d))

    adding more water to the system

Show Answer
Answer: ((a))

increasing the system pressure

158

Which of the following screwdrivers has cross-shaped tips that are unlikely to slip from the cruciform slots in Philips recessed head screws?

  1. ((a))

    Offset screwdriver 

  2. ((b))

    Stumpy screwdriver

  3. ((c))

    Ratchet screwdriver 

  4. ((d))

    Cross-recess screwdriver 

Show Answer
Answer: ((a))

Offset screwdriver 

159

Why do cars have treaded tyres?

  1. ((a))

    To increase friction and grip on the road

  2. ((b))

    To increase speed 

  3. ((c))

    To decrease friction 

  4. ((d))

    To reduce weight 

Show Answer
Answer: ((a))

To increase friction and grip on the road

160

What is the primary reason for conducting a vehicle road test? 

  1. ((a))

    To increase fuel efficiency 

  2. ((b))

    To test how fast the vehicle can go

  3. ((c))

    To ensure the vehicle is functioning safely and correctly 

  4. ((d))

    To avoid the need for inspections 

Show Answer
Answer: ((a))

To increase fuel efficiency 

161

An angle greater than 180 degrees is referred to as ________________. 

  1. ((a))

    a right angle

  2. ((b))

     an acute angle 

  3. ((c))

    a reflex angle 

  4. ((d))

    an obtuse angle

Show Answer
Answer: ((a))

a right angle

162

The hand priming device is used to:

  1. ((a))

    increase fuel pressure for combustion

  2. ((b))

    control the fuel injection timing 

  3. ((c))

     pump fuel from the tank to the Fuel Injection Pump (FIP)

  4. ((d))

     inject fuel into the engine cylinder 

Show Answer
Answer: ((a))

increase fuel pressure for combustion

163

Which of the following types of materials is NOT used in an oil filter as a strainer?

  1. ((a))

    Wire screen 

  2. ((b))

    Felt

  3. ((c))

    Thin aluminum foil

  4. ((d))

    Cloth

Show Answer
Answer: ((a))

Wire screen 

164

In a circuit with a NTC type thermistor and a fixed resistor connected in series connected to a DC power supply, what will happen to the output voltage if there is a rise in temperature?

  1. ((a))

    The output voltage will fluctuate depending on the resistor value.

  2. ((b))

     The output voltage will decrease. 

  3. ((c))

    The output voltage will remain constant.

  4. ((d))

    The output voltage will increase. 

Show Answer
Answer: ((a))

The output voltage will fluctuate depending on the resistor value.

165

Which of the following is a key electrical safety tip in a workshop? 

  1. ((a))

    Use water to clean electrical panels 

  2. ((b))

    Operate machines with wet hands

  3. ((c))

    Ensure electrical equipment is properly grounded 

  4. ((d))

    Ignore frayed wires if the device is still working 

Show Answer
Answer: ((a))

Use water to clean electrical panels 

166

In what form is the speed of information processing in the ECM (Engine Control Module) typically measured?

  1. ((a))

    Bar

  2. ((b))

    RPM (Revolutions Per Minute)

  3. ((c))

    Bits (8-bit, 16-bit, 32-bit, etc.)

  4. ((d))

    Volts

Show Answer
Answer: ((a))

Bar

167

What is the primary goal of the 5S concept? 

  1. ((a))

    To replace traditional safety measures 

  2. ((b))

     To eliminate the need for maintenance  

  3. ((c))

    To increase the number of safety regulations 

  4. ((d))

    To improve workplace organisation and efficiency

Show Answer
Answer: ((a))

To replace traditional safety measures 

168

The piston rings are placed in the ring groove and provide sealing between which of the following two parts to prevents leakage of high-pressure gases?

  1. ((a))

     Piston and the cylinder head 

  2. ((b))

    Piston and the cylinder fins 

  3. ((c))

    Piston and the cylinder liner

  4. ((d))

    Piston and the cylinder block 

Show Answer
Answer: ((a))

 Piston and the cylinder head 

169

Evaporative emissions are primarily caused by: 

  1. ((a))

    fuel leaking onto the ground 

  2. ((b))

    fuel burning in the engine  

  3. ((c))

    exhaust gases escaping from the tailpipe

  4. ((d))

     fuel evaporating from the fuel tank and carburetor 

Show Answer
Answer: ((a))

fuel leaking onto the ground 

170

The SI unit of 'ultimate stress' is ________. 

  1. ((a))

    joule per square meter (J/m² )

  2. ((b))

    newton per meter (N/m)

  3. ((c))

    newton (N)

  4. ((d))

    pascal (Pa) 

Show Answer
Answer: ((a))

joule per square meter (J/m² )

171

In a two stroke petrol engine, during the upward stroke of the piston, the gases are compressed in the piston, and at the same time, which of the following is also performed during the operation? 

  1. ((a))

    Fresh air and fuel (petrol) mixture enters the crank chamber through the valve.

  2. ((b))

    Fresh fuel enters in the cylinder from the crank chamber through the valve. 

  3. ((c))

    Fresh air for petrol engine enters the cylinder from the chamber through the valve exhaust port.

  4. ((d))

    Exhaust gases enter the crank chamber through the valve. 

Show Answer
Answer: ((a))

Fresh air and fuel (petrol) mixture enters the crank chamber through the valve.

172

Which of the following types of seats is made of hardened alloys and pressed or shrunk into the cylinder head, often used in aluminium engines for better durability? 

  1. ((a))

    Ring valve seats 

  2. ((b))

    Butterfly valve seats 

  3. ((c))

    Integral valve seats 

  4. ((d))

    Insert valve seats

Show Answer
Answer: ((a))

Ring valve seats 

173

Which of the following processes is used to fit a bearing into the connecting rod, allowing the gudgeon pin to provide the oscillating movement at the small end of the connecting rod?

  1. ((a))

    Loose fit  

  2. ((b))

    Interference fit

  3. ((c))

    Press fit 

  4. ((d))

    Autofrettage fit 

Show Answer
Answer: ((a))

Loose fit  

174

In Variable Geometry Turbochargers (VGT), if the aspect ratio is too small, the turbo will likely: 

  1. ((a))

    work perfectly at all speeds

  2. ((b))

    reduce exhaust manifold pressure 

  3. ((c))

    fail to create boost at low speeds

  4. ((d))

    choke the engine at high speeds 

Show Answer
Answer: ((a))

work perfectly at all speeds

175

During regenerative braking, the electric motor acts as a:

  1. ((a))

    heater

  2. ((b))

    compressor

  3. ((c))

    pump

  4. ((d))

    generator

Show Answer
Answer: ((a))

heater

Attempt this paper under real exam conditions

Timed interface, section switching, instant scoring, and question-by-question analytics — free.

Start Timed Attempt